2026-02-28

ECU - Charge Port (7-Seat) (Remove and Replace)

Correction code TBD FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Remove

  1. Open all four doors and lower all windows.
  2. Open the hood via the touchscreen.
  3. Move the 1st row LH and RH seats forward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust the seat back to avoid contact with the headliner if needed.
  4. Open the liftgate.
  5. Press the shoulder switch and push the 2nd row seats forward to position the seats into the easy entry mode.
  6. Power off the vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Note
    On the touchscreen, touch Controls > Safety > Power Off > Power Off.
  7. Remove the HEPA filter. See HEPA Filter Assembly (Remove and Replace).
  8. Remove the 3rd row seat cushion. See Seat Cushion - 3rd Row (7-Seat) (Remove and Replace).
  9. Press the front switch at the LH trunk trim panel to release the 3rd row LH seat backrest.
  10. Press the rear switch at the LH trunk trim panel to release the 3rd row RH seat backrest.
  11. Disconnect the LV power. See LV Power (Disconnect and Connect) (Modify).
  12. Remove the rear load floor.
  13. Remove the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
  14. Remove the LH trunk pocket bracket. See Pocket Bracket - LH (7-Seat) (Remove and Replace).
  15. Release the remaining clips, and then remove the LH 7s trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x push clip, 2x clip tabs, 4x Guide tabs
  16. Release the LH trunk side trim and disconnect the 12V outlet connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 7x tabs, 1x connector
  17. Disconnect the charge port ECU connectors (x3).
  18. Remove the bolt that attaches the charge port ECU to the vehicle, and then slide the charge port ECU to the right, and then remove the charge port ECU from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    10mm

Install

  1. Install the charge port ECU by sliding it into the slots (x2) of the vehicle body, and then install the bolt that attaches the charge port ECU to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    10mm, 9 Nm
  2. Connect the charge port ECU connectors (x3).
  3. Position the LH trunk side trim and install the lower clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x push clips, 5x clips,
    Informational PurposesAn informational icon, calling your attention
    Note
    Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly. Guide the front clip stanchions around the LH C-pillar.
  4. Install the LH trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    7x tabs, 4x clips, 1x location pin, 1x connector
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the trunk seal is properly seated against the edge of the trim.
  5. Install the LH trunk pocket bracket. See Pocket Bracket - LH (7-Seat) (Remove and Replace).
  6. Connect the LV power. See LV Power (Disconnect and Connect) (Modify).
  7. Install the 3rd row seat cushion. See Seat Cushion - 3rd Row (7-Seat) (Remove and Replace).
  8. Move the 1st row and 2nd row seats back to their original positions.
  9. Install the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
  10. Raise the 3rd row RH seat backrest to its original position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manually raise the backrest up to its original position until it locks into place.
  11. Raise the 3rd row LH seat backrest to its original position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Manually raise the backrest up to its original position until it locks into place.
  12. Install the rear load floor.
  13. Close the liftgate.
  14. Reinstall the vehicle firmware. See Software Reinstall - Touchscreen.
  15. Raise all windows and close all doors.