2025-03-12

Shell - Seat Back - 2nd Row - LH (Remove and Replace)

Correction code 1308011802 FRT 0.00 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the 2nd row LH seat assembly. See 2ND ROW SEAT 5 SEATER - 60 (Remove and Replace).
  2. Place 2nd row 60 seat assembly on a safe and stable work area.
  3. Remove headrest from 2nd row 60 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged.
  4. Remove LH seatback from 60 seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 5 hooks, Starting from upper left release all clips, detach lower hooks afterwards.
  5. Remove the LH outboard headrest guide lock.
  6. Remove the LH inboard headrest guide lock.
  7. Remove 60 escutcheon from 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Pry upwards on front of 60 escutcheon and remove, Take note of tab locators, Separate 60 escutcheon from seat belt
  8. Remove lower anchor bolt for 2nd row center retractor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T50, 40 Nm, Discard after removal
  9. Remove clips securing seat back shell to seat rail
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips
  10. Disconnect 2nd row Seat backrest adjustment motor connection
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  11. Release 2nd row Seat backrest adjustment motor connection clips
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 2x harness hooks
  12. Release seat position sensor clip
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  13. Disconnect seat position sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  14. Separate seat back assembly from seat rail
    Informational PurposesAn informational icon, calling your attention
    Note
    3x hooks, 1x tab, Push tab forward, And Lift up and unhook from seat railing
  15. Feed center retractor seat belt through seat back assembly
  16. Remove 60 seat harness from seat back shell
    Informational PurposesAn informational icon, calling your attention
    Note
    2x hooks, 3x tabs, 1x clip, 1x connector
  17. Release 60 seat back assembly trim flaps from seat back shell
    Informational PurposesAn informational icon, calling your attention
    Note
    2x hooks, 22x tabs, Pull seat back trim flaps down and then away from upholstery support tabs to release
  18. Remove 60 seat back heat pad harness from seat back shell
    Informational PurposesAn informational icon, calling your attention
    Note
    3x hooks, 1x clip
  19. Remove seat back shell from foam trim assembly

Install

  1. Install seat back shell to foam assembly
  2. Install 60 seat back heat pad harness to seat back shell
    Informational PurposesAn informational icon, calling your attention
    Note
    3x hooks, 1x clip
  3. Install 60 soft trim cover flaps to seat back shell
    Informational PurposesAn informational icon, calling your attention
    Note
    2x hooks, 22x tabs
  4. Install 60 seat harness to seat back shell
    Informational PurposesAn informational icon, calling your attention
    Note
    2x hooks, 3x tabs, 1x clip, 1x connector
  5. Feed center retractor seat belt through seat back assembly
  6. Install upholstery support onto seat rail
    Informational PurposesAn informational icon, calling your attention
    Note
    3x hooks, 1x tab
  7. Connect seat position sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  8. Install seat position sensor clip
    Informational PurposesAn informational icon, calling your attention
    Note
    1x clip
  9. Install 2nd row Seat backrest adjustment motor connection clips
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 2x harness hooks
  10. Connect 2nd row Seat backrest adjustment motor connection
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  11. Install clips securing upholstery support to seat rail
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips
  12. Install lower anchor bolt for 2nd row center retractor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T50, 40 Nm, Install new bolt, Ensure that seat belt is not twisted and installed correctly
  13. Install 60 escutcheon to 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, Install 60 escutcheon onto seat belt, Guide 60 escutcheon into locating tabs, Secure 60 escutcheon clips onto 60 seat assembly
  14. Install LH outboard headrest guide lock
  15. Install LH inboard headrest guide lock
  16. Install LH seat back panel onto 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 5 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips
  17. Install headrest onto 60 seat assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Push down to secure
  18. Install the 2nd row LH seat assembly. See 2ND ROW SEAT 5 SEATER - 60 (Remove and Replace).