2025-03-12

WINDOW REGULATOR CLOSEOUT FRONT DOOR - LEFT HAND (Remove and Replace)

Correction code 1150010502 FRT 0.55 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: WINDOW REGULATOR CLOSEOUT FRONT DOOR - LEFT HAND (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x11) that attach the LH front door closeout panel to the door
4.5 Nm (3.3 lbs-ft)
  • 8 mm socket
Reuse
Bolts (x2) that attach the regulator rail fasteners to the vehicle
8 Nm (5.9 lbs-ft)
  • 10 mm socket
Reuse
Screws (x4) that attach the window regulator to the closeout panel
3.5 Nm (2.6 lbs-ft)
  • Torx T25 socket
Reuse

Remove

  1. Remove the LH front door glass. See MOVING SIDE GLASS - FRONT DOOR - LEFT HAND (Remove and Replace).
  2. Disconnect the LV power. See LV Power (Disconnect and Connect).
  3. Remove the LH front door pressure sensor. See DOOR PRESSURE SENSOR (Remove and Replace).
  4. Remove the LH front window regulator motor. See Window Regulator - Front Door - LH (Remove and Install).
  5. Remove the LH front door speaker. See Speaker - Front Door (Remove and Replace).
  6. Disconnect the electrical connector from the LH front door mirror.
  7. Release the clips (x4) that attach the electrical wiring harness to the LH front door closeout panel and set it aside.
  8. Remove the plugs (x2) that cover the regulator rail fasteners.
  9. Remove the bolts (x11) that attach the LH front door closeout panel to the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 8 mm socket
  10. Remove the bolts (x2) that attach the regulator rail fasteners to the vehicle, and then remove the closeout panel assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the closeout panel down and out.
    Informational PurposesAn informational icon, calling your attention
    Note
    The window regulator and closeout panel are removed attached.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Remove the screws (x4) that attach the window regulator to the closeout panel.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  12. Release the hook and datums (x3) that attach the window regulator to the closeout panel, and remove the regulator from the panel.

Install

  1. Install the datums (x3), and then install the screws (x4) that attach the window regulator to the closeout panel.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  2. Install the hook that attaches the window regulator to the closeout panel.
  3. Position the LH front door closeout panel assembly to the door, and then install the bolts (x2) that attach the regulator rail fasteners to the vehicle.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the closeout panel in and up.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Install the bolts (x11) that attach the LH front door closeout panel to the door.
    4.5 Nm (3.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 8 mm socket
  5. Install the plugs (x2) that cover the regulator rail fasteners.
  6. Install the clips (x4) that attach the electrical wiring harness to the LH front door closeout panel.
  7. Connect the electrical connector to the LH front door mirror.
  8. Install the LH front door speaker. See Speaker - Front Door (Remove and Replace).
  9. Install the LH front window regulator motor. See Window Regulator - Front Door - LH (Remove and Install).
  10. Install the LH front door pressure sensor. See DOOR PRESSURE SENSOR (Remove and Replace).
  11. Connect the LV power. See LV Power (Disconnect and Connect).
  12. Install the LH front door glass. See MOVING SIDE GLASS - FRONT DOOR - LEFT HAND (Remove and Replace).