2026-06-24

Hood Latch (Remove and Replace)

Correction code 1133040202 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Torque Specifications

  • 2026-03-27: Added steps to run Frunk Latch Metric Reset.
Table 1. Torque Specifications: Hood Latch (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the hood latch to the front end carrier
8 Nm (5.9 lbs-ft)
  • 10 mm socket
 Reuse

Remove

Informational PurposesAn informational icon, calling your attention
Note
If the hood latch does not open electronically, use the manual front trunk release tool to open the hood.
  • 1130534-00-ATOOL, FRUNK RELEASE, MANUAL, MODEL 3
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
When using the manual front trunk release tool in Mobile Service, raise the vehicle using mini ramps and verify stability of the vehicle.
  1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace) or Underhood Storage Unit (Model Y Standard) (Remove and Install).
  2. Disconnect the electrical connector from the hood latch.
  3. Release the hood latch actuator cable from the hood latch.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the clip before removing the actuator cable from the latch arm.
  4. Remove the bolts (x2) that attach the hood latch to the front end carrier, and then remove the latch from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark the hood latch location on the front end carrier.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Install the hood latch to the front end carrier, and adjust the latch actuator position based on marks.
  2. Tighten the bolts (x2) that attach the hood latch to the front end carrier.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Fully tighten the bolts before adjustment. The latch may move if the bolts are only hand-tightened.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the hood latch actuator cable to the hood latch.
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure the cable end to the latch arm, and then attach the clip.
  4. Connect the electrical connector to the hood latch.
  5. Close the hood and verify alignment is within specification. If necessary, loosen the bolts that attach the hood latch to the front end carrier, adjust the hood latch, and then fully tighten the bolts (x2)
    8 Nm (5.9 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not adjust the hood striker. Only make small adjustments to the hood latch, and then make sure the bolts are fully tightened.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace) or Underhood Storage Unit (Model Y Standard) (Remove and Install).
  7. Place the vehicle into Service Mode. See Service Mode.
  8. On the vehicle touchscreen, navigate to Service Mode > Closures > Frunk
  9. Tap Frunk Latch Metric Reset, tap Confirm, and then tap Run and allow the routine to complete.
  10. Exit Service Mode. See Service Mode.
  11. Raise the LH front window and close the LH front door.