2025-03-12

C PILLAR AIRBAG RAMP - LEFT HAND (Remove and Replace)

Correction code 1518011802 FRT 0.45 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications:C PILLAR AIRBAG RAMP - LEFT HAND (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH coathook screw
2.5 Nm (1.8 lbs-ft)
  • Ratchet/torque wrench
  • 4 in extension
  • Torx T25 socket
  • Torque wrench 1/4" hexagon (0.2Nm-4Nm) (Installation only)
Reuse
Bolt securing LH airbag ramp to body
5 Nm (3.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 10 mm socket
  • Ratchet; Wrench, Torque+Angle, 1/4" Dr.(Installation only)
Reuse

Remove

  1. Remove the LH trunk side trim. See TRUNK SIDE TRIM LEFT HAND - REAR UNDER BODY (Remove and Replace).
  2. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  3. Remove the rear headliner panel. See REAR HEADLINER (Remove and Replace).
  4. Push open LH coathook, and open LH coathook screw cover.
  5. Remove LH coathook screw.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • Torx T25 socket
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm) (Installation only)
  6. Release LH rear section of headliner from body.
  7. Remove bolt securing LH airbag ramp to body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • Ratchet; Wrench, Torque+Angle, 1/4" Dr.(Installation only)
  8. Remove LH airbag ramp.

Install

  1. Install LH airbag ramp.
  2. Install bolt securing LH airbag ramp to body.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • Ratchet; Wrench, Torque+Angle, 1/4" Dr.(Installation only)
  3. Secure LH rear section of headliner to body.
  4. Install LH coathook screw.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • Torx T25 socket
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm) (Installation only)
  5. Close LH coathook screw cover and push LH coathook closed.
  6. Install the rear headliner panel. See REAR HEADLINER (Remove and Replace).
  7. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  8. Install the LH trunk side trim. See TRUNK SIDE TRIM LEFT HAND - REAR UNDER BODY (Remove and Replace).