CABIN CARPET - FRONT - RIGHT HAND (Remove and Replace)
Correction code
1530030302
FRT
0.20
NOTE: Unless
otherwise explicitly stated in the procedure, the above correction code and
FRT reflect all of the work required to perform this procedure, including
the linked procedures. Do
not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate Times to learn more about FRTs and how they are
created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.
NOTE: See Personal Protection to make
sure wearing proper PPE when performing the below procedure.
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolts (x4) that attach the driver seat to body |
![]() 33.5 Nm (24.7 lbs-ft) |
|
Replace | 1458818-00-A |
Remove
- Open the RH front door and lower the RH front window.
- Remove the RH lower A-pillar trim. See A PILLAR LOWER TRIM - LEFT HAND (Remove and Install).
- Release the RH front seat harness from the sill trim clips (x4).
- Pull the RH front seat harness from under the RH front cabin carpet.
- Move the RH front seat forward.
- Open the RH rear door and lower the RH rear window.
-
Remove and discard the RH front seat rear bolts.
TIpUse of the following tool(s) is recommended:
- Cordless Ratchet/Impact Driver
- Torx Plus TP45 Bit Socket
- Ratchet/torque wrench
- Move the RH front seat backward.
-
Remove and discard the RH front seat front bolts.
TIpUse of the following tool(s) is recommended:
- Cordless Ratchet/Impact Driver
- Torx Plus TP45 Bit Socket
- Ratchet/torque wrench
-
Tilt the RH front seat backward.
NoteNo need to disconnect the RH seat harness from the body controller.
-
Remove the RH footwell hush panel. See Hush Panel - Footwell - Front Passenger (Remove and Replace).
NoteNo need to separate the puddle lamp from the passenger footwell hush panel.
- Remove the RH front center console side panel. See CONSOLE SIDE PANEL RIGHT HAND (Remove and Replace).
-
Release the push clips (x2) that
attach the RH front cabin carpet to the body, and then remove the RH front carpet from
the vehicle.
NoteLift up the rear edge of the carpet and then slide it out towards the rear of vehicle. Be cautious to avoid the foam below catching on the seat risers.
Install
- Place the RH front cabin carpet into the vehicle, and then install the push clips (x2) that attach the carpet to the body.
- Install the RH front center console side panel. See CONSOLE SIDE PANEL RIGHT HAND (Remove and Replace).
- Install the RH footwell hush panel. See Hush Panel - Footwell - Front Passenger (Remove and Replace).
- Return the RH front seat to installation position.
-
Install new RH front seat front bolts
(x2) (1458818-00-A).33.5 Nm (24.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- Cordless Ratchet/Impact Driver
- Torx Plus TP45 Bit Socket
- Ratchet/torque wrench
- Move the RH front seat forward.
-
Install new RH front seat rear bolts
(x2) (1458818-00-A).33.5 Nm (24.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- Cordless Ratchet/Impact Driver
- Torx Plus TP45 Bit Socket
- Ratchet/torque wrench
- Raise the RH rear window and close the RH rear door.
- Move the RH front seat to original position.
- Secure the RH front seat harness under the RH front cabin carpet.
-
Install the RH front seat harness to the sill trim clips (x4).
NoteTuck the excess harness between the harness bracket and body.
- Install the RH lower A-pillar trim. See A PILLAR LOWER TRIM - LEFT HAND (Remove and Install).
- Raise the RH front window and close the RH front door.