2026-07-30

Rear End Module - Center Console (Model YL) (Remove and Install)

Correction code 15190201901 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-07-22: Updated the steps from removing the hockey sticks to partially releasing them for enough access space.

Torque Specifications

Table 1. Torque Specifications: Rear End Module - Center Console (Model YL) (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x6) that attach the rear end module assembly to the center console
1.2 Nm (.9 lbs-ft)
  • Torx T20 bit
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
 Reuse
Bolt that attaches the rear end module assembly to the center console
1.2 Nm (.9 lbs-ft)
  • Torx T20 bit
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
 Replace 1096312-00-A

Remove

  1. Disconnect the LV battery power. See LV Power (Disconnect and Connect) (Modify).
  2. Remove the 2nd row cup holder assembly. See Cup Holder Assembly - 2nd Row (Model YL) (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    During removal, certain steps require extra care. See the animation(s) for detailed guidance.
  3. Lift up the armrest.
  4. Partially release the LH hockey stick and place an inflatable air bag for enough space to access the rear display fasteners.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x location tab, 1x guide tab
    Figure 1. LH shown; RH similar
  5. Partially release the RH hockey stick and place an inflatable air bag for enough space to access the rear display fasteners.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x location tab, 1x guide tab
  6. Remove the screws (x6) that attach the rear end module assembly to the center console.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  7. Release the datums (x2) to release the rear end module assembly from the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not take the assembly fully away as the harness is still attached.
  8. Disconnect the electrical connectors (x2), and then remove and discard the bolt that attaches the rear end module assembly to the center console.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm

Install

  1. Install a new bolt (1096312-00-A) that attaches the rear end module assembly to the center console, and then connect the electrical connectors (x2).
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  2. Secure the datums (x2) to install the rear end module assembly to the center console.
  3. Install the screws (x6) that attach the rear end module assembly to the center console.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  4. Remove the inflatable air bag, then secure the LH hockey stick onto the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x location tab, 1x guide tab
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the guide tab is properly installed.
    Figure 2. LH shown; RH similar
  5. Remove the inflatable air bag, then secure the RH hockey stick onto the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 1x location tab, 1x guide tab
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the guide tab is properly installed.
  6. Put down the armrest.
  7. Install the 2nd row cup holder assembly. See Cup Holder Assembly - 2nd Row (Model YL) (Remove and Replace).
  8. Connect the LV battery power. See LV Power (Disconnect and Connect) (Modify).
  9. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox (Connect and Disconnect).
  10. In Toolbox, click the Actions tab, type "PING-BASH_DISPLAY" into the search field, click PING-BASH_DISPLAYvia Toolbox:(link), select rear in the Poppyseed Display Test Arg drop-down list and enter 20 in the Timeout field, then click Run, and allow the routine to complete.
  11. Disconnect the laptop.
  12. Exit Service Mode. See Service Mode.