2025-03-12

PIPE L - REAR BRAKE (Remove and Replace)

Correction code 3303010702 FRT 0.55 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
Informational PurposesAn informational icon, calling your attention
Note
Dispose of used brake fluid in a manner consistent with local environmental codes.

Torque Specifications

Table 1. Torque Specifications: PIPE L - REAR BRAKE (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes

LH rear brake line tube outer nut

Nut that attaches the LH rear brake line to the LH rear brake hose

16 Nm (11.8 lbs-ft)
  • 12 mm 6-point flare nut wrench
  • Ratchet/torque wrench
  • 12 mm 6-point flare nut crowfoot socket (mount at 90 degrees)
Reuse

Remove

  1. Place the vehicle on the 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Ensure the vehicle is not charging.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the LH rear wheel arch liner. See WHEEL LINER - REAR - LEFT HAND (Remove and Replace).
  4. Position the oil drain under the rear brake line junction block.
  5. Remove the LH rear brake line tube nut from the LH rear brake pipe junction block.
  6. Remove the LH rear brake line tube outer nut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12 mm 6-point flare nut wrench
    • Ratchet/torque wrench
    • 12 mm 6-point flare nut crowfoot socket (mount at 90 degrees)
  7. Position the oil drain under the LH rear brake hose area.
  8. Remove the nut that attaches the LH rear brake line to the LH rear brake hose.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12 mm 6-point flare nut wrench
    • Ratchet/torque wrench
    • 12 mm 6-point flare nut crowfoot socket (mount at 90 degrees)
  9. Remove the clips (x3) that attach the brake line to the body, and then remove the brake line from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    No bending of the brake line is allowed.

Install

  1. Install the clips (x3) that attach the brake line to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    No bending of the brake line is allowed.
  2. Hand-tighten the LH rear brake line tube outer nut, and then torque it.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12 mm 6-point flare nut wrench
    • Ratchet/torque wrench
    • 12 mm 6-point flare nut crowfoot socket (mount at 90 degrees)
  3. Hand-tighten the nut that attaches the LH rear brake line to the LH rear brake hose, and then torque it.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12 mm 6-point flare nut wrench
    • Ratchet/torque wrench
    • 12 mm 6-point flare nut crowfoot socket (mount at 90 degrees)
  4. Remove the oil drain under the LH rear brake hose area.
  5. Lower the vehicle to a comfortable working height and set the lift onto locks.
  6. Place the vehicle in Service Mode by using the touchscreen. See Service Mode.
  7. Unlock the vehicle gateway. See Gateway (Unlock).
  8. Perform a brake fluid flush on the LH rear brake. See .
  9. Install the LH rear wheel arch liner. See WHEEL LINER - REAR - LEFT HAND (Remove and Replace).
  10. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  11. Perform a road test using a series of aggressive stops to make sure there is proper pedal feel and brake performance.
    Informational PurposesAn informational icon, calling your attention
    Note
    Add test drive correction code 00040100 as a separate activity to the Service Visit.