2025-03-12

FRONT LOWER COMPLIANCE LINK - LEFT HAND (Remove and Replace)

Correction code 3101030102 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: FRONT LOWER COMPLIANCE LINK - LEFT HAND (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut that attaches the front lower compliance link to the knuckle
180 Nm (132.7 lbs-ft)
  • 22 mm deep socket
  • Flex head ratchet/flex head torque wrench
  • Cordless Ratchet/Impact Driver
Replace 1109263-00-B
Bolt and nut that attach the LH front compliance link to the front subframe
115 Nm (84.8 lbs-ft)
  • 21 mm socket
  • Breaker bar
  • 3 in extension
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
Reuse

Remove

  1. Inspect the vehicle for abnormal tire wear that might indicate the need for a wheel alignment. Note any findings.
  2. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  3. Remove the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
  4. Remove and discard the nut that attaches the LH front lower compliance link to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 22 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  5. Remove the bolt and nut that attach the LH front lower compliance link to the front subframe, and then remove the link from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
    • Breaker bar
    • 3 in extension
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench

Install

  1. With assistance, position the LH front lower compliance link to the front subframe, and then install the bolt and nut that attach the LH front lower compliance link to the front subframe.
    115 Nm (84.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
    • Breaker bar
    • 3 in extension
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  2. Hand-tighten a new nut that attaches the LH front lower compliance link to the knuckle, and then torque the nut.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 22 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  3. Install the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
  4. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  5. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.