2025-01-23

Brace - Shock Tower (Remove and Replace)

Correction code TBD FRT 0.5 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications:Brace - Shock Tower (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the ground strap to the A/C compressor
7 Nm (5.2 lbs-ft)
  • Torx T25 socket
Reuse
Bolts (x2) that attach the A/C compressor assembly to the brace
31 Nm (22.9 lbs-ft)
  • 15 mm socket
Reuse
Bolts (x2) that attach the supermanifold to the shock tower brace
31 Nm (22.9 lbs-ft)
  • 15 mm socket
Reuse
The LH and RH bolts (x4) that attach the shock tower brace to the body
55 Nm (40.6 lbs-ft)
  • 15 mm socket
Reuse
The LH and RH outer bolts that attach the shock tower brace to the body
62 Nm (45.7 lbs-ft)
  • 15 mm socket
Reuse

Remove

  1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  2. Remove the cabin intake duct. See Duct - Air Intake (Remove and Replace).
  3. Remove LV power. See 16V LI - ION BATTERY (Remove and Install).
  4. Use a clip pry tool to release the clips (x4) that attach the coolant hose to the A/C compressor bracket.
  5. Release the connector locking tab, and then disconnect the HVIL connector near the LH front strut tower.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  6. Release the connector locking tab, then disconnect the A/C logic electrical connector from the A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  7. Use a clip pry tool to release the retaining clip that attaches the A/C compressor logic harness to the A/C compressor HV harness bracket.
  8. Remove the bolt that attaches the ground strap to the A/C compressor, and then set the ground strap aside.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  9. Use a clip pry tool to release the clip that attaches the coolant hose to the A/C compressor bracket.
  10. Remove the retaining clips (x5) that attach the A/C compressor HV harness to the shock tower brace.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull upward on the clip to assist with removal. Do not pull upward on the HV cable.
  11. Place a fender cover (1115212-00-A) on the front underhood storage unit reinforcement beam to prevent damage to other components.
  12. With an assistant, remove the bolts (x2) that attach the A/C compressor assembly to the strut tower brace, and then carefully maneuver the assembly towards the front of the vehicle, under the strut tower support brace. Rest the A/C compressor assembly on the front underhood storage unit reinforcement beam.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not rest the A/C compressor on the HV connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  13. Secure the supermanifold assembly with bungee cords.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install bungee cord to RH hood strut bracket. Route bungee cord around accumulator housing and secure to the RH body side. Do not secure bungee cord around coolant pumps or plastic housing on supermanifold. Use a mirror as needed to visual check bungee cord around accumulator housing.
  14. Remove the bolts (x2) that attach the supermanifold to the shock tower brace.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  15. Remove the LH and RH bolts (x4) that attach the shock tower brace to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  16. Remove the LH and RH outer bolts (x2) that attach the shock tower brace to the body, and then remove the shock tower brace from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket

Install

  1. Position the shock tower brace to the vehicle, and then loosely install the LH and RH bolts (x6) that attach the shock tower brace to the body.
  2. Torque the LH and RH outer bolts (x2) that attach the shock tower brace to the body.
    62 Nm (45.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  3. Torque the LH and RH bolts (x4) that attach the shock tower brace to the body.
    55 Nm (40.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  4. With an assistant supporting the A/C compressor assembly under the strut tower brace, install the bolts (x2) that attach the supermanifold to the shock tower brace.
    31 Nm (22.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  5. Remove the bungee cords from the supermanifold assembly.
  6. With an assistant supporting the A/C compressor assembly under the strut tower brace, hand-start the bolts (x2) that attach the A/C compressor assembly to the brace, and then torque the bolts.
    31 Nm (22.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  7. Remove the fender cover from the front underhood storage unit support beam.
  8. Install the retaining clips (x5) that attach the A/C compressor HV harness to the shock tower support brace.
  9. Install the clip that attaches the coolant hose to the A/C compressor bracket.
  10. Position the ground strap on the A/C compressor, and then install the bolt that attaches the ground strap to the A/C compressor.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  11. Install the retaining clip that attaches the A/C compressor logic harness to the A/C compressor HV harness bracket.
  12. Connect the A/C compressor logic electrical connector to the A/C compressor, and then engage the locking tab.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  13. Connect the HVIL connector near the LH front strut tower, and then engage the locking tab.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  14. Install the clips (x4) that attach the coolant hose to the A/C compressor bracket.
  15. Install LV power. See 16V LI - ION BATTERY (Remove and Install).
  16. Remove the cabin intake duct. See Duct - Air Intake (Remove and Replace).
  17. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).