Correction code 1309010601 1309010602 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

1. Open all four doors

   

2. Lower all four windows

   

3. Open liftgate

   

4. Move LH front seat forward

   

5. Position 60 seat into easy entry mode
   Note

   Press shoulder switch and push 60 seat forward to position into easy entry mode

   

   

6. Move RH front seat forward

   

7. Position 40 seat into easy entry mode
   Note

   Press shoulder switch and push 40 seat forward to position into easy entry mode

   

   

8. Remove 3rd row seat cushion and disconnect harness
   Note

   1x connector, Pull LH and RH release lever under 3rd row seat cushion to release seat cushion

   

   

   

9. Remove 3rd row LH seat cushion bolster
   Note

   1x bolt, 13mm, 37 Nm, Slide LH seat cushion bolster towards front of vehicle to remove

   

   

10. Remove bolt securing 3rd row LH seat belt retractor to seat frame assembly
    Note

    1x bolt, 11mm, 37 Nm, Discard bolt after removal

    

11. Remove rear load floor

    

12. Remove 3rd row LH back panel from LH seatback assembly
    Note

    10x clips, 2x guide hooks, Once cover clips are disengaged, slide back panel up and away from 3rd row seat for full removal

    

    

13. Remove 3rd row LH headrest
    Note

    Depress guide button, Insert pick into guide opening, Lift headrest upwards and remove

    

    

14. Remove 3rd row LH adjustment guide from LH headrest closeout panel
    Note

    1x tab, Release detent tab at rear of seat, then pry adjustment guide upwards to release from seat

    

    

15. Remove 3rd row RH adjustment guide from RH headrest closeout panel
    Note

    1x tab, Release detent tab at rear of seat, then pry adjustment guide upwards to release from seat

    

    

    

16. Remove 3rd row LH headrest closeout panel from LH backrest
    Note

    Lift upward to remove LH headrest closeout panel

    

17. Remove 3rd row LH shoulder switch from LH backrest
    Note

    2x clips, 1x connector

    

    

18. Remove 3rd row LH escutcheon from LH backrest
    Note

    2x clips

    

19. Remove fasteners securing 3rd row LH backrest to LH seatback assembly
    Note

    2x fasteners, T25, 2.5 Nm

    

20. Release clips securing 3rd row LH backrest to LH seatback assembly
    Note

    4x clips, Push clips in to remove from frame

    

21. Remove 3rd row LH backrest from LH seatback assembly
    Note

    2x tabs

    

22. Remove 3rd row LH trim cover from LH back substrate
    Note

    26x tabs, Release RH tabs then LH tabs

    

    

    

    

    

    

23. Install 3rd row LH trim cover to LH back substrate
    Note

    26x tabs, Install LH tabs then RH tabs

    

    

    

    

    

24. Install 3rd row LH backrest to LH seatback assembly
    Note

    2x tabs, 4x clips

    

    

    

25. Install fasteners securing 3rd row LH backrest to LH seatback assembly
    Note

    2x fasteners, T25, 2.5 Nm

    

26. Install 3rd row LH escutcheon into LH backrest
    Note

    2x clips

    

27. Install 3rd row LH shoulder switch into LH backrest
    Note

    2x clips, 1x connector

    

    

28. Install 3rd row LH closeout panel into LH backrest
    Note

    2x tabs

    

29. Install 3rd row RH adjustment guide into LH closeout panel

    

30. Install 3rd row LH adjustment guide into LH closeout panel

    

31. Install 3rd row LH headrest
    Note

    Depress adjustment guides during installation

    

32. Install 3rd row LH back panel to LH seatback assembly
    Note

    2x tabs, 10x clips

    

    

33. Install rear load floor

    

34. Install bolt securing 3rd row LH seat belt retractor to seat frame assembly
    Note

    1x bolt, 11mm, 37 Nm, Bolt is one time use

    

35. Install 3rd row LH seat cushion bolster
    Note

    1x bolt, 13mm, 37 Nm, Slide LH seat cushion bolster into seat frame assembly

    

    

36. Install 3rd row seat cushion and connect harness
    Note

    1x connector, Secure 3rd row seat cushion into RH and LH latches

    

    

37. Move 60 seat to original position

    

38. Move LH front seat to original position

    

39. Move 40 seat to original position

    

40. Move RH front seat to original position

    

41. Raise all four windows

    

42. Close all four doors
    Note

    If LV is powered up, Unlatch rear doors before closing

    

43. Close liftgate