2025-03-12

REAR LEFT BLUETOOTH LOW ENERGY (Remove and Replace)

Correction code 1715010502 FRT 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Table 1. Torque Specifications: REAR LEFT BLUETOOTH LOW ENERGY (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH corner of the rear fascia assembly to the body
3.5 Nm (2.6 lbs-ft)
  • 10 mm socket
Reuse
Bolt that attaches the LH side of the rear fascia assembly to the body
2 Nm (1.5 lbs-ft)
  • 8 mm socket
Reuse
Bolt that attaches LH corner of the rear fascia diffuser to the body
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • 4 in extension
  • Ratchet/torque wrench
Reuse

Remove

  1. Open the liftgate.
  2. Apply masking tape around the LH corner of the rear fascia to protect the paint on the vehicle.
  3. Use a plastic trim tool to release the clips (x3) that attach the LH rear trough trim to the rear fascia, and then partially release the lower section of the trough trim from the fascia.
  4. Remove the bolt that attaches the LH corner of the rear fascia assembly to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Remove the LH rear fender garnish. See Garnish - Fender - Rear - LH (Remove and Replace).
  6. Remove the bolt that attaches the LH side of the rear fascia assembly to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  7. Remove the bolt that attaches the LH corner of the rear fascia diffuser to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
    • Ratchet/torque wrench
  8. Partially loosen the LH rear fascia.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to use excessive force, as there are still bolts and clips on the rear fascia that have not been removed.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care of not damaging the tabs.
  9. Carefully insert inflatable air bag between the rear fascia and the body to gain access to the BLE assembly.
  10. Disconnect the LH rear BLE connector.
  11. Release the tabs (x2) that attach the LH rear BLE assembly to the rear fascia, and then remove the BLE assembly from the vehicle.

Install

  1. Install the lower part of the LH rear BLE assembly to the bracket, and then secure that tabs (x2) that attach the BLE assembly to the rear fascia.
  2. Connect the LH rear BLE connector.
  3. Deflate and remove the inflatable air bag,and then install the rear fascia back to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that all tabs are engaged.
  4. Install the bolt that attaches LH corner of the rear fascia diffuser to the body.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • 4 in extension
    • Ratchet/torque wrench
  5. Install the bolt that attaches the LH side of the rear fascia assembly to the body.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  6. Install the LH rear fender garnish. See Garnish - Fender - Rear - LH (Remove and Replace).
  7. Install the bolt that attaches the LH corner of the rear fascia assembly to the body.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Install the clips (x3) that attach the LH rear trough trim to the rear fascia.
  9. Remove the masking tapes from around the LH corner of the rear fascia.
  10. Close the liftgate.