2026-08-04

Assembly - Tail Lamp - Liftgate (Remove and Replace)

Correction code 1740030502 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-08-03: Due to part changes, removed the liftgate camera and handle steps and added liftgate extension harness steps.
  • 2026-06-30: Removed the DAS routines,
  • 2025-12-24: Add a note to make sure the liftgate is closed all the time.
  • 2025-09-08: Added step to apply masking tape to the liftgate before removing tail lamp.
  • 2025-06-11: Updated the torque and routine.
Informational PurposesAn informational icon, calling your attention
Note
Make sure the liftgate is closed during the process.

Torque Specifications

Table 1. Torque Specifications: Assembly - Tail Lamp - Liftgate (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x4) that attach the lamp to the liftgate
4 Nm (2.9 lbs-ft)
  • Torx T30 socket
 Reuse
Nuts (x2) that attach the lamp to the liftgate
5 Nm (3.7 lbs-ft)
  • 10 mm deep socket
 Reuse
Exterior bolts (x3) that attach the lamp to the liftgate
3.5 Nm (2.6 lbs-ft)
  • 10 mm deep socket
 Reuse

Remove

  1. Remove the spoiler outer panel. See Spoiler Outer Panel (Remove and Replace).
  2. Disconnect the liftgate extend harness connectors (x2).
  3. Remove the liftgate extend harness from the liftgate assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pay attention to the grommet installed orientation and the harness route path on both sides of the liftgate, so that the harness can be installed to its original position during installation.
  4. Remove the bolts (x4) that attach the lamp to the liftgate.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  5. Remove the nuts (x2) that attach the lamp to the liftgate.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  6. Remove the bolts (x3) that attach the lamp to the liftgate.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  7. Apply masking tape to the liftgate below the tail lamp assembly to protect the painted surface.
  8. Remove the tail lamp assembly from the liftgate.

Install

  1. Install the tail lamp assembly to the liftgate.
  2. Remove the masking tape from the liftgate.
  3. Install the exterior bolts (x3) that attach the lamp to the liftgate.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  4. Install the nuts (x2) that attach the lamp to the liftgate.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  5. Install the bolts (x4) that attach the lamp to thee liftgate.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  6. Install the liftgate extend harness to the liftgate assembly and install the grommet.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the grommet in the same orientation as removed and make sure that the harness is routed correctly.
  7. Connect the liftgate extend harness connectors (x2).
  8. Install the spoiler outer panel. See Spoiler Outer Panel (Remove and Replace).
  9. Place the vehicle in Service Mode by using the touchscreen. See Service Mode.
  10. Unlock the vehicle gateway. See Gateway (Unlock).
  11. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Driver Assist > Cameras > Clear Camera Calibration, select RearView in the Camera Selection drop list, click Run, and allow the routine to complete.
  12. Tap Driver Assist > Cameras > Update Camera, select BACKUP, click Run, and allow the routine to complete.
  13. Exit Service Mode. See Service Mode.
  14. Raise the LH front window and close the LH front door.
  15. Inform the customer that the vehicle needs to be driven by the customer to complete the calibration procedure.