2026-05-20

Supermanifold V2 - 16MM Check Valve (Model YL) (Remove and Replace)

Correction code 18400100502 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Informational PurposesAn informational icon, calling your attention
Note
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate correction within the same activity to the Service Visit.

Remove

  1. Set up the AC machine.
  2. Unlock the vehicle gateway. See Gateway (Unlock).
  3. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Refrigerant System > Start Refrigerant Fill/Drain > Run, and allow the routine to complete.
  4. Power off the vehicle from the center display.
    Informational PurposesAn informational icon, calling your attention
    Note
    On the touchscreen, touch Controls > Safety > Power Off > Power Off.
  5. Remove the HEPA filter assembly. See HEPA Filter Assembly (Remove and Replace).
  6. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  7. Recover the A/C refrigerant. See A/C Refrigerant (Recovery and Recharge) (Restore).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Make sure there is no overpressure in the A/C system before performing the following steps. Failure to do so may result in damage to components and/or personal injury.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    HFO-R1234yf and R134a are considered hazardous and, if handled incorrectly, can cause serious injury. Suitable personal protective equipment, consisting of face and eye protection, safety glasses, face shield, heat-proof gloves, chemical resistant gloves, rubber boots and apron or waterproof overall must be worn when carrying out operations on the air conditioning system.
  8. Remove A/C machine hoses from the vehicle.
  9. Carefully depress the Schrader valves (x2) to level out any pressure difference between the A/C system pressure and the actual ambient atmospheric pressure.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure to depress both Schrader valves. Failure to do so may result in injury.
  10. Remove the bolt that attaches the supermanifold-to-compressor A/C line to the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm socket
  11. Remove the supermanifold-to-compressor A/C line from the supermanifold, and move it aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Carefully position the line so that oil does not drip out.
  12. Remove and discard the check valve snap ring from the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use adjustable joint pliers to pull the snap ring outwards to remove the ring.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Wear the Face Shield throughout the entire process to protect against foreign objects flying out under pressure.
  13. Remove the check valve from the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the O-ring is not left inside the bore.

Install

  1. Lubricate O-rings on the check valve with the appropriate A/C oil. See for A/C oil specifications. Then install the check valve into the supermanifold.
  2. Install a new check valve snap ring into the supermanifold.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Wear the Face Shield throughout the entire process to protect against foreign objects flying out under pressure.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the snap ring is properly seated inside the groove on the supermanifold.
  3. Install new seal washers on the supermanifold side of the supermanifold-to-compressor A/C line, and then lubricate the washers with a small amount of the appropriate A/C oil. See Fluids and Capacities for A/C oil specifications.
  4. Position the supermanifold to compressor A/C line onto the supermanifold, and then hand-tighten the bolt that attaches the A/C line to the supermanifold.
  5. Tighten the bolt that attaches the supermanifold to compressor A/C line to the supermanifold.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm socket
  6. Perform the vacuum leak test and oil injection, and A/C refrigerant recharge. See A/C Refrigerant (Recovery and Recharge) (Restore).
  7. Install the HEPA filter assembly. See HEPA And Carbon Filters (Remove and Replace).
  8. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  9. Unlock the vehicle gateway. See Gateway (Unlock).
  10. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Refrigerant System > Stop Refrigerant Fill/Drain > Run, and allow the routine to complete.
  11. Tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Refrigerant System > Run Commission Heat Pump > Run, and allow the routine to complete.
  12. Exit Service Mode. See Service Mode.
  13. Raise the LH front window and close the LH front door.