2025-03-12

DOOR - NOISE VIBRATION HARNESS PAD - FRONT LEFT HAND (Remove and Replace)

Correction code 1513010302 FRT 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Open the LH front door, and lower the LH front window.
  2. Remove the LH tweeter. See Tweeter - Front Door - LH (Remove and Replace).
  3. Remove the LH front door reflector. See DOOR REFLECTOR (Remove and Replace).
  4. Remove the bolts (x3) that attach the trim panel to the LH front door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  5. Use a plastic trim tool to insert the inflatable air bag to the lower left corner of the LH front door trim, then inflate it to release the lower left clip(s).
  6. Continue to pull and release all of the clips around the edge of the trim panel, working from the bottom up.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull the trim panel far away from the door as the panel is still attached by connectors and cables.
  7. Release the manual release cable from the cable bracket and then remove the cable collar from the trim panel and pivot the collar down to a vertical orientation.
  8. Slide the cable barrel end out of the release lever, and remove the cable from the trim panel.
  9. Put the LH front door trim panel on a padded and stable support.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull the trim panel far away from the door as the panel is still attached by connectors and cables.
  10. Release the NVH pad from the tabs, and then remove it from the LH front door trim panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not pull the trim panel far away from the door as the panel is still attached by connectors.

Install

  1. Install the LH front door NVH pad onto the LH front door trim panel.
  2. Position the manual release cable in a vertical orientation, and slide the cable barrel end into the release lever.
  3. Pivot the manual release cable collar to a horizontal orientation and press the collar into the trim panel, and then secure the cable to the cable bracket.
  4. Lift the trim panel, compress the LH front door inner belt seal slightly, and then hook the trim panel tabs into the top edge of the door.
  5. Fasten the clips that attach the trim panel to the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any broken clips.
  6. Make sure that the trim panel fits tightly, and that there are no gaps from misaligned or bent clips.
  7. Install the bolts (x3) that attach the trim panel to the LH front door.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure that all fasteners are properly torqued and not cross-threaded.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  8. Install the LH front door reflector. See DOOR REFLECTOR (Remove and Replace).
  9. Install the LH tweeter. See Tweeter - Front Door - LH (Remove and Replace).
  10. Close the door and verify the operation of the manual door release lever, that the door latch releases smoothly and easily.
  11. Raise the LH front window and close the door.