SECOND ROW - CENTER SEAT BELT RETRACTOR (Remove and Replace)
Correction code
2005020102
FRT
0.00
NOTE: Unless
otherwise explicitly stated in the procedure, the above correction code and
FRT reflect all of the work required to perform this procedure, including
the linked procedures. Do
not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate Times to learn more about FRTs and how they are
created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.
NOTE: See Personal Protection to make
sure wearing proper PPE when performing the below procedure.
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Lower anchor bolt that attaches the seat belt to the LH 2nd row seat frame |
![]() 40 Nm (29.5 lbs-ft) |
|
Replace | |
Bolt that attaches the seat belt retractor assembly to the seat frame |
![]() 45 Nm (33.2 lbs-ft) |
|
Replace |
Remove
- Open all doors and fully lower all windows.
- Move both front seats to their foremost position.
- Remove the 2nd row lower seat cushion. See 2ND ROW SEAT CUSHION (Remove and Replace).
- Remove the LH 2nd row 60 seat assembly from vehicle. See 2ND ROW SEAT 5 SEATER - 60 (Remove and Replace)
-
Place the 2nd row seat frame assembly
on a safe and stable work area.
NoteFold down the center section of the 2nd row rear seat, and then place a ballast bag on the center section to stabilize the assembly.
-
Release the LH 2nd
row headrest clips simultaneously, and then pull the headrest upwards to remove
it.
NoteUse a pocket screwdriver to release the LH headrest clip.
-
Remove the headrest guide
locks from the LH 2nd row seat back.
NoteUse a wedge tool to lift up the guide locks from the seat.
- Release the clips (x2) that attach the seat belt bezel to the LH 2nd row seat back.
- Release the clips (x2) that attach the 2nd row seat back switch bezel to the seat back, and then remove the bezel from the seat back.
-
Remove the 2nd row seat soft back trim
and foam from the seat back frame.
NoteRelease the soft back trim from the top, and then release the lower hooks.
-
Remove and discard the lower anchor
bolt that attaches the seat belt to the LH 2nd row seat frame.
TIpUse of the following tool(s) is recommended:
- 13 mm socket
- Flex head ratchet/flex head torque wrench
- 6 in extension
- Release the clips (x2) that attach the LH outside cover to the LH 2nd row seat back, and then separate the cover from the seat back.
- Remove the clips that attach the LH 2nd row seat back cushion to the seat rail.
- Disconnect the 2nd row seat back heater electrical connector, and then release the clip that attaches the connector to the seat back.
-
Separate the LH 2nd row seat back
cushion from the seat rail.
NotePull up to unhook the seat from the railing.
- Feed the center seat belt through the LH 2nd row seat back.
-
Remove and discard the bolt that
attaches the seat belt retractor assembly to the seat frame, and then remove it from the
seat back.
TIpUse of the following tool(s) is recommended:
- 13 mm deep socket
- 6 in extension
Install
-
Install the seat belt retractor
assembly to the seat frame, and then install a new bolt to attach the retractor assembly
to the seat frame.45 Nm (33.2 lbs-ft)TIpUse of the following tool(s) is recommended:
- 13 mm deep socket
- 6 in extension
- Move the center seat belt through the LH 2nd row seat back.
-
Install the LH 2nd row seat back
cushion to the seat rail.
NotePush down to hook the seat to the railing.
- Connect the 2nd row seat back heater electrical connector, and then fasten the clip that attaches the connector to the seat back.
- Fasten the clips that attach the LH 2nd row seat back cushion to the seat rail.
- Install the LH outside cover to the LH 2nd row seat back, and then fasten the clips (x2) that attach the cover to the seat back.
-
Install the seat belt anchor to the LH
2nd row seat frame, and then install a new bolt to attach the anchor to the frame.40 Nm (29.5 lbs-ft)TIpUse of the following tool(s) is recommended:
- 13 mm socket
- Flex head ratchet/flex head torque wrench
- 6 in extension
-
Install the 2nd row seat soft back
trim and foam to the seat back frame.
NoteFasten the lower hooks, and then fasten the soft back trim to the top.
- Install the 2nd row seat back switch bezel to the seat back, and then fasten the clips (x2) that attach the bezel to the seat back.
- Fasten the clips (x2) that attach the seat belt bezel to the LH 2nd row seat back.
- Install the headrest guide locks to the LH 2nd row seat back.
- Install the LH 2nd row headrest, and then fasten the clips that attach the LH 2nd row headrest to the 2nd row seat back.
- Install the 2nd row seat frame assembly into the vehicle.
- Install the LH 2nd row 60 seat assembly to vehicle. See 2ND ROW SEAT 5 SEATER - 60 (Remove and Replace)
- Install the 2nd row lower seat cushion. See 2ND ROW SEAT CUSHION (Remove and Replace).
- Return both front seats to their previous position.
- Close all doors and windows.