2026-02-12

Front Brake Pad Kit - Sport (Remove and Install)

Correction code 3301011001 0.00 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-02-12: Released new procedure.
Equipment:
  • 1082171-10-A/1082171-00-A - S-hook
  • 1134786-00-A - Brake Caliper Spreader M3
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
Informational PurposesAn informational icon, calling your attention
Note
Dispose of used brake fluid in a manner consistent with local environmental codes.

Torque Specifications

Table 1. Torque Specifications: Front Brake Pad Kit - Sport (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH front brake hose bracket to the knuckle
5 Nm (3.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 4 in extension
  • 10 mm socket
  • Ratchet/torque wrench
 Reuse
Bolts (x2) that attach the LH front brake caliper to the knuckle
94 Nm (69.3 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • External Torx E18
  • Breaker bar
  • 3/8 in to ½ in adapter
  • Ratchet/torque wrench
 Replace 1088969-00-B

Procedure

  1. Prepare the vehicle for raising. See Raise Vehicle - 2-Post Lift.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure that the vehicle is not charging.
  2. Open the LH front door and lower the window.
  3. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  4. Place absorbent material underneath the brake fluid reservoir area.
  5. Clean the area around the brake fluid reservoir and remove the brake reservoir cap.
  6. Remove the LH and RH front wheels. See Wheel Assembly (Remove and Install).
  7. Remove the bolt that attaches the LH front brake hose bracket to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  8. Remove the front brake caliper anti-rattle springs (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a plastic trim tool to avoid damaging the coating of the caliper.
  9. Remove and discard the bolts (x2) that attach the LH front brake caliper to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • Breaker bar
    • 3/8 in to ½ in adapter
    • Ratchet/torque wrench
  10. Remove the LH front brake caliper and hang it off to a firm part beside with an S-hook.
    Informational PurposesAn informational icon, calling your attention
    Note
    Preferentially use S-hook 1082171-10-A. If 1082171-10-A is not available, use 1082171-00-A instead.
    Informational PurposesAn informational icon, calling your attention
    Note
    S-hook 1082171-10-A can only be hung on metal parts.
  11. Use the brake caliper spreader to spread the brake pads as wide as possible to push the piston into a position for easy installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 1134786-00-A - Brake Caliper Spreader M3
  12. Remove the brake pads from the LH front brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the adhesive between the pads and the pistons with a trim tool.
  13. Clean the front brake caliper anti-rattle springs.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a nylon brush and brake cleaner as needed. Allow 1 minute to dry after cleaning.
  14. Clean the LH front brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a nylon brush and brake cleaner as needed. Allow 1 minute to dry after cleaning.
  15. Use a plastic trim tool to remove the sticky shims from the front brake pads.
  16. Clean the front brake pads.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure pads are on a clean surface. Clean any debris with a hand brush. Clean the back side of the pads with IPA wipes, and allow 1 minute dry time.
  17. Apply sticky shims onto the backside of the brake pads.
    Informational PurposesAn informational icon, calling your attention
    Note
    Cut the sticky shim to 5 cm x 5 cm and center it out on the back side of the pad's piston surface. Make sure that the double sided tape mates onto the brake pad.
  18. Apply an even layer of Silaramic lubricant onto the brake pad guide contact points.
  19. Remove the protective film from the sticky shims on the brake pads.
  20. Install the brake pads into the LH front brake caliper.
  21. Install the bolts (x2) that attach the LH front brake caliper to the knuckle.
    94 Nm (69.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • Breaker bar
    • 3/8 in to ½ in adapter
    • Ratchet/torque wrench
  22. Install the front brake caliper anti-rattle springs (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care not to damage the coating of the brake caliper, and make sure that the springs are fully installed.
  23. Install the bolt that attaches the LH front brake hose bracket to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  24. Repeat steps 7 through 23 on the RH side of the vehicle.
  25. Install the LH and RH front wheels. See Wheel Assembly (Remove and Install).
  26. Check the brake fluid reservoir and top off as necessary.
  27. Remove the absorbent material from underneath the brake fluid reservoir area.
  28. Pump the brake pedal a few times to seat the pads against the brake rotor until the brake pedal feels firm.
  29. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  30. Burnish the brakes. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    Note
    During vehicle driving, make sure that proper brake pedal feel and performance is achieved.
    Informational PurposesAn informational icon, calling your attention
    Note
    Add the correction code for brake pad burnishing 33013000 as a separate activity to the Service Visit.