Rear Suspension Arms - Rear Upper Aft Link (Remove and Replace)
Correction code
3103030502
FRT
0.35
NOTE: Unless
otherwise explicitly stated in the procedure, the above correction code and
FRT reflect all of the work required to perform this procedure, including
the linked procedures. Do
not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate Times to learn more about FRTs and how they are
created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com.
NOTE: See Personal Protection to make
sure wearing proper PPE when performing the below procedure.
- 1457016-00-A KIT, SPRING COMPRESSOR, GEDORE
- 1081765-00-A 3/4 TON UNDERHOIST STAND
- 1459409-00-A ADAPTER, HUB JACK, MODEL 3
Torque Specifications
Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
---|---|---|---|---|
Bolt and nut that attach the LH rear upper aft link to the LH rear knuckle |
![]() 134 Nm (98.8 lbs-ft) |
|
Reuse | |
Bolt and nut that attach the LH rear upper aft link to the subframe |
![]() 134 Nm (98.8 lbs-ft) |
|
Reuse |
Remove
-
Inspect the tires for abnormal
wear.
NoteNote any abnormal tire wear that could indicate the need for an alignment.
- Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
- Remove the LH rear suspension cover. See Rear Suspension Cover - LH (Remove and Replace).
-
Remove the bolt and nut that attach
the LH rear upper aft link to the LH rear knuckle.
TIpUse of the following tool(s) is recommended:
- 21 mm socket
- Flex head ratchet/flex head torque wrench
-
Remove the bolt and nut that attach
the LH rear upper aft link to the subframe.
TIpUse of the following tool(s) is recommended:
- 21 mm combination wrench
- 21 mm socket
- Flex head ratchet/flex head torque wrench
- Remove the LH rear upper aft link from the vehicle.
Install
-
Position the LH rear upper aft link
onto the subframe, and then install and hand-tighten the bolt and nut.
NoteMake sure that the tab points vertically to the ground.
- Position the LH rear upper aft link onto the knuckle, and then install and hand-tighten the bolt and nut.
-
Install a spring compressor onto the
LH rear suspension spring:
WarningSprings in a compressed state are under large amounts of energy. Refer to the Tool Profile for the spring compressor kit prior to performing this step for additional warnings and cautions.
-
Remove the bolt that attaches the LH
rear brake rotor to the hub.
TIpUse of the following tool(s) is recommended:
- 10 mm socket
- Cordless Ratchet/Impact Driver
- 2 in extension
- Install the hub jack adapter onto the LH rear hub and hand-tighten the lug nuts (x5).
- Position and raise the underhoist stand to simulate the suspension at ride height.
- Measure the distance between the bottom of the quarter panel and the center of the rear axle to make sure that the rear suspension is set to ride height. The distance should measure 428 mm.
-
Tighten the bolt and nut that attach
the LH rear upper aft link to the subframe. Mark the bolt with a paint pen.134 Nm (98.8 lbs-ft)TIpUse of the following tool(s) is recommended:
- 21 mm combination wrench
- 21 mm socket
- Flex head ratchet/flex head torque wrench
-
Tighten the bolt and nut that attach
the LH rear upper aft link to the knuckle, and then mark the bolt and nut with a paint
pen.134 Nm (98.8 lbs-ft)TIpUse of the following tool(s) is recommended:
- 21 mm socket
- Flex head ratchet/flex head torque wrench
- Remove the underhoist stand from underneath the LH rear suspension.
- Remove the lug nuts (x5) that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
-
Install the bolt that attaches the LH
rear brake rotor to the hub.5 Nm (3.7 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10 mm socket
-
Remove the spring compressor from the
LH rear suspension spring:
WarningBe careful while unloading the spring. Hold the spring horizontally and facing away from you.WarningSprings in a compressed state are under large amounts of energy. Refer to the Tool Profile for the spring compressor kit prior to performing this step for additional warnings and cautions.
- Install the LH rear suspension cover. See Rear Suspension Cover - LH (Remove and Replace).
- Install the LH rear wheel. See Wheel Assembly (Remove and Install).
- Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.