2025-01-23

Brake Rotor - Rear - Base - LH (Remove and Replace)

Correction code 3301020502 FRT 0.25 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • Brake Caliper S-Hook
Informational PurposesAn informational icon, calling your attention
Note
For detailed brake specifications, see Brakes.

Torque Specifications

Table 1. Torque Specifications: Brake Rotor - Rear - Base - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH rear brake caliper to the LH rear knuckle
83 Nm (61.2 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • External Torx E18
  • 3 in extension
  • Ratchet/torque wrench
Replace
Bolt that attaches the LH rear brake rotor to the hub
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • Cordless Ratchet/Impact Driver
  • 2 in extension
Reuse

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Stands.
  2. Open the LH front door and lower the LH front window.
  3. Enter Service Mode. See Service Mode.
  4. Unlock the vehicle gateway. See Gateway (Unlock).
  5. Press the brake pedal.
  6. On the touchscreen, touch Chassis > Brakes > EPB Service Mode, and select Both in EPB Selection, select START in Action Selection, and then click Run.
  7. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  8. Remove and discard the bolts (x2) that attach the LH rear caliper to the LH rear knuckle, remove the caliper from the knuckle, and allow the caliper to hang from an S-hook.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • 3 in extension
    • Ratchet/torque wrench
  9. Remove the bolt that attaches the LH rear brake rotor to the hub.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • 2 in extension
  10. Remove the LH rear rotor from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Store the rotor face down to reduce likelihood of damage to the rotor face.

Install

  1. Install the LH rear rotor onto the vehicle.
  2. Install the bolt that attaches the LH rear brake rotor to the hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install new bolts (x2) that attach the LH rear caliper to the LH rear knuckle.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • 3 in extension
    • Ratchet/torque wrench
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To prevent damage to the flexible brake hose, make sure that the brake hose can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
  4. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  5. On the touchscreen, touch Chassis > Brakes > EPB Service Mode, and select Both in EPB Selection, select STOP in Action Selection, and then click Run.
  6. Exit Service Mode. See Service Mode.
  7. Raise the LH front window and close the LH front door.
  8. Lower the vehicle. See Raise Vehicle - 2 Stands.