2026-01-08

Damper Coil - Dual Motor - Front - LH (Remove and Replace)

Correction code 3115010102 FRT 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-01-08: Added steps to remove/install LH wiper bracket pencil brace.
  • 2025-05-20: Removed instruction to remove/install the bolt that attaches the LH front rotor to the LH front hub.

Torque Specifications

Table 1. Torque Specifications: Damper Coil - RWD - Front - LH (Remove and Replace) and Damper Coil - Dual Motor - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH brace to the vehicle
18.8 Nm (13.9 lbs-ft)
  • 10 mm socket
 Reuse
Bolt and nut that attach the LH front lower lateral link to the strut
106 Nm (78.2 lbs-ft)
  • 21 mm socket
Reuse
Nut that attaches the front stabilizer bar end link to the LH front strut
98 Nm (72.3 lbs-ft)
  • 18 mm socket
  • Torx T40 socket
Replace 1111543-00-A
Nuts (x3) that attach the front upper control arm mount to the LH front spring and damper assembly
23 Nm (17.0 lbs-ft)
  • 13 mm socket
Reuse

Remove

  1. Inspect the vehicle for abnormal tire wear that might indicate the need for a wheel alignment. Note any findings.
  2. Raise and support the vehicle. See Raise Vehicle - 2-Post Lift.
  3. Remove the HEPA filter. See HEPA Filter Assembly (Remove and Replace).
  4. Remove the LH wiper bracket pencil brace. See Pencil Brace - Wiper Bracket - LH (Remove and Replace).
  5. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  6. Release the clips (x2) that attach the LH front ABS wheel speed sensor to the upper control arm.
  7. Remove and discard the nut that attaches the front stabilizer bar end link to the LH front strut and separate the end link from the strut.
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter-hold the ball joint while loosening the nut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    If needed, use a pry bar to release the end link.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18 mm socket
    • Torx T40 socket
  8. Remove the bolt and nut that attach the LH front lower lateral link to the strut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  9. Remove the bolt and nut that attach the LH front upper control arm to the knuckle, and then discard the nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    Compress the upper control arm ball joint downwards to help release the bolt.
    Informational PurposesAn informational icon, calling your attention
    Note
    Hold the knuckle to avoid failing.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
    • Torx T50 socket
  10. Remove the nuts (x3) that attach the LH front damper assembly to the LH front upper control arm mount.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  11. Remove the damper assembly from the vehicle.

Install

  1. Maneuver the damper assembly into place.
  2. Hand tighten the bolt and nut that attach the LH strut to the LH front lower lateral link.
  3. Install the nuts (x3) that attach the LH front damper assembly to the LH front upper control arm mount.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  4. Position the LH upper control arm to the knuckle, and then install the bolt and a new nut that attach the LH front upper control arm to the knuckle.
    56 Nm (41.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
    • Torx T50 socket
  5. Position the front stabilizer end link onto the LH front strut, and then install a new nut that attaches the front stabilizer end link to the LH front strut.
    98 Nm (72.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter-hold the ball joint while torquing the nut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    If needed, use a pry bar to help position the end link.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18 mm socket
    • Torx T40 socket
  6. Install the clips (x2) that attach the LH front ABS wheel speed sensor to the upper control arm.
  7. Install the hub jack adapter onto the LH front hub and hand-tighten the lug nuts (x5).
  8. Position and raise the underhoist stand to simulate the suspension at ride height.
  9. Measure the distance between the bottom of the fender and the center of the front axle to make sure that the front suspension is set to ride height. The distance should measure 461 mm.
  10. Tighten the bolt and nut that attach the LH front lower lateral link to the strut.
    106 Nm (78.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
  11. Remove the underhoist stand from underneath the LH front suspension.
  12. Remove the lug nuts (x5) that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
  13. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  14. Install the LH wiper bracket pencil brace. See Pencil Brace - Wiper Bracket - LH (Remove and Replace).
  15. Install the HEPA filter. See HEPA Filter Assembly (Remove and Replace).
  16. Remove the vehicle from the lift. See Raise Vehicle - 2-Post Lift.
  17. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.