2026-07-03

Instrument Panel Steering Column Upper Gap Hider (Remove and Replace)

Correction code 3205010602 FRT 1.50 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Torque Specifications

Table 1. Torque Specifications: Instrument Panel Steering Column Upper Gap Hider (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (X2) securing steering column upper gap hider to steering column
2.3 Nm (1.7 lbs-ft)
  • Torx T25 bit
  • 4 in extension
  • Ratchet/torque wrench
 Reuse
Nuts (X2) securing the steering column to the cross car beam
15 Nm (11.1 lbs-ft)
  • Ratchet/torque wrench
  • 13 mm socket
 Reuse

Remove

  1. Open the LH front door, lower the LH front window, and move the LH front seat backward.
  2. On the touchscreen, tap Controls > Steering, and use the left scroll wheel to adjust the steering column fully outward and fully downward.
  3. Disconnect the LV battery power. See LV Power (Disconnect and Connect) (Modify).
  4. Remove the instrument panel lower assembly. See Assembly - Instrument Panel - Lower (Remove and Replace).
  5. Remove the steering column lower gap hider. See Gap Hider - Steering Column - Lower (Remove and Replace)
  6. Loosen the two screws that secure the steering column upper gap hider to the steering column.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • 4 in extension
    • Ratchet/torque wrench
  7. Apply protective tape to the instrument panel surface surrounding the steering column assembly.
  8. Remove the nuts (x2) that secure the steering column to the cross car beam, and remove the steering column upper gap hider from the steering column.
    15 Nm (11.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13 mm socket
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Check for broken clip pieces on the connector, and remove if present.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not allow the full weight of the steering column to rest on the plastic instrument panel structure to prevent structural damage. Request assistance as needed to support the column during removal or installation.

Install

  1. Install the steering column upper gap hider to the steering column, and then install the nuts (x2) that secure the steering column to the cross car beam.
    15 Nm (11.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13 mm socket
  2. Remove the protective tape from the instrument panel surface and clean the area.
  3. Install the two screws that secure the steering column upper gap hider to the steering column.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • 4 in extension
    • Ratchet/torque wrench
  4. Install the steering column lower gap hider. See Gap Hider - Steering Column - Lower (Remove and Replace)
  5. Install the instrument panel lower assembly. See Assembly - Instrument Panel - Lower (Remove and Replace).
  6. Connect the LV battery power. See LV Power (Disconnect and Connect) (Modify).
  7. On the touchscreen, touch Controls > Steering, use the left scroll wheel to adjust the steering column back to its original position, and then touch Save.
  8. Move the LH front seat back to its original position, raise the LH front window, and close the LH front door.