2025-03-12

Fender - LH (Remove and Replace)

Correction code 1010030102 FRT 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Fender - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x5) and nuts (x2) that attach the LH front fender bracket to the body
9.8 Nm (7.2 lbs-ft)
  • 10 mm deep socket
Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Disconnect the LV battery power. See LV Power (Disconnect and Connect).
  3. Remove the front lightbar assembly. See Lightbar - Front (Remove and Install).
  4. Remove the front fascia assembly. See FRONT FASCIA (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    No need to separate the valance, the front fascia harness and the grille from the front fascia assembly.
  5. Remove the LH headlamp. See Headlamp Assembly - Pair (Remove and Install).
  6. Remove the LH fascia side bracket from fender. See Bracket - Fascia Side to Fender - LH (Remove and Replace).
  7. Disconnect the cowl screen from the LH carrier bracket.
  8. Remove the bolts (x5) that attach the LH front fender bracket to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  9. Remove the nuts (x2) that attach the LH lower front fender bracket to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  10. Disconnect the side repeater connectors (x2).
  11. Remove the LH front fender assembly from the vehicle.
  12. Release the clip and tabs (x2) to remove the LH side repeater.
    Informational PurposesAn informational icon, calling your attention
    Note
    Press to release the clip.
  13. Remove the frunk fender clips (x3) from the LH front fender.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any damaged clip.
  14. Release the clips (x2) to remove the headlamp rubber grommet from the LH front fender.

Install

  1. Secure the clips (x2) to install the headlamp rubber grommet onto the LH front fender.
  2. Install the frunk fender clips (x3) onto the LH front fender.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any damaged clip.
  3. Secure the clip and the tabs (x2) to install the LH side repeater onto the fender.
    Informational PurposesAn informational icon, calling your attention
    Note
    When the side repeater is installed in place, a noticeable "click" sound can be heard.
  4. Connect the LH side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the lock on camera connection is secure.
  5. Position the LH front fender assembly onto the vehicle.
  6. Install the nuts (x2) that attach the LH lower front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  7. Install the bolts (x5) that attach the LH front fender bracket to the body.
    9.8 Nm (7.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  8. Secure the cowl screen clip to the LH carrier bracket.
  9. Install the LH fascia side bracket from fender. See Bracket - Fascia Side to Fender - LH (Remove and Replace).
  10. Install the LH headlamp. See Headlamp Assembly - Pair (Remove and Install).
  11. Install the front fascia assembly. See FRONT FASCIA (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    After installing the clips (x4) that attach the LH and RH front wheel arch liner to the front fascia assembly, check gap and flushness for the fender, and adjust if necessary. Refer to CVIS for current specification.
  12. Install the front lightbar assembly. See Lightbar - Front (Remove and Install).
  13. Connect the LV battery power. See LV Power (Disconnect and Connect).
  14. Remove all the protective tapes.
  15. Raise the LH front window and close the LH front door.
  16. Remove the vehicle from the lift.