2025-01-21

Seat Back - 2nd Row - LH (Remove and Replace)

Correction code TBD FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Seat Back - 2nd Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the lower anchor to the 2nd row center retractor
40 Nm (29.5 lbs-ft)
  • Torx T50 socket
Replace 2000419-00-A

Remove

  1. Remove the 2nd row LH seat assembly. See 2ND ROW SEAT 5 SEATER - 60 (Remove and Replace).
  2. With assistance, position the 2nd row LH seat assembly onto a padded surface.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold down the center armrest to stabilize the weight. Prevent the seat assembly from tipping over. Use a ballast bag and any additional support as needed.
  3. Remove the 2nd row LH seat headrest. See SECOND ROW OUTER HEADREST (Remove and Replace).
  4. Remove the 2nd row LH seat outboard and inboard headrest guide locks. See Seats - 2nd Row Seat Assemblies and Hardware - 2nd Row Seat Assemblies - 2nd Row Headrest Guide Lock - LH (RI).
  5. Remove the 2nd row LH escutcheon. See SECOND ROW ESCUTCHEON - LEFT HAND (Remove and Replace).
  6. Remove and discard the bolt that attaches the lower anchor to the 2nd row center retractor.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  7. Remove the clips (x3) that attach the 2nd row LH seatback substrate to the frame.
  8. Disconnect the 2nd row LH seat backrest adjustment motor connector.
  9. Release the 2nd row LH seat backrest adjustment motor harness from the substrate.
  10. Release the 2nd row LH seat position sensor connector clip.
  11. Disconnect the 2nd row LH seat position sensor connector.
  12. Release hooks (x3) and a tab to remove the 2nd row LH seat substrate from the frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the tab forward, and then lift up and unhook the substrate from the seat frame.
  13. Pull the center retractor seat belt out of the seatback assembly.
  14. Release the 2nd row LH seatback harness from the shell, disconnect the connector, and then pull the seatback assembly away from the rail.

Install

  1. Connect the 2nd row LH seatback harness connector, secure the harness to the shell, and insert the assembly into the rail.
  2. Feed the center retractor seat belt through the seat back assembly.
  3. Secure hooks (x3) and a tab to install the 2nd row LH seat substrate to the frame.
  4. Connect the 2nd row LH seat position sensor connector.
  5. Install the 2nd row LH seat position sensor connector clip.
  6. Install the 2nd row LH seat backrest adjustment motor harness to the substrate.
  7. Connect the 2nd row LH seat backrest adjustment motor connector.
  8. Install the clips (x3) that attach the 2nd row LH seatback substrate to the frame.
  9. Install a new bolt that attaches the lower anchor to the 2nd row center retractor.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that seat belt is not twisted and is installed correctly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  10. Install the 2nd row LH escutcheon. See SECOND ROW ESCUTCHEON - LEFT HAND (Remove and Replace).
  11. Install the 2nd row LH seat outboard and inboard headrest guide locks. See Seats - 2nd Row Seat Assemblies and Hardware - 2nd Row Seat Assemblies - 2nd Row Headrest Guide Lock - LH (RI).
  12. Install the 2nd row LH seat headrest. See SECOND ROW OUTER HEADREST (Remove and Replace).
  13. Install the 2nd row LH seat assembly. See 2ND ROW SEAT 5 SEATER - 60 (Remove and Replace).