2025-03-12

SECOND ROW SEAT SWITCH POWER RECLINE - RIGHT HAND (Remove and Replace)

Correction code 1305031502 FRT 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: SECOND ROW SEAT SWITCH POWER RECLINE - RIGHT HAND (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the recliner switch to the recliner switch assembly
0.7 Nm (6 lbs-in)
  • Torx T20 socket
  • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
Reuse
Bolts (x2) that attach the recliner switch to the seat cushion foam.
1 Nm (.7 lbs-ft)
  • 10 mm socket
  • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
Reuse

Remove

  1. Remove the 2nd row seat cushion. See 2ND ROW SEAT CUSHION (Remove and Replace).
  2. Remove the bolts (x2) that attach the recliner switch assembly to the seat cushion foam.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
  3. Disconnect the RH rear seat recliner switch connector.
  4. Release the retaining clips (x3) that attach the seat cushion foam to the cushion assembly.
  5. Release the tabs that attach the recliner switch assembly to the switch bezel, and then remove the recliner switch assembly from the seat cushion.
  6. Remove the bolts (x2) that attach the recliner switch to the recliner switch assembly, and then remove the switch from the switch assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm)

Install

  1. Install the bolts (x2) that attach the recliner switch to the recliner switch assembly.
    0.7 Nm (6 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
  2. Install the recliner switch assembly to the seat cushion, and then install the tabs that attach the recliner switch assembly to the switch bezel.
  3. Install the retaining clips (x3) that attach the seat cushion foam to the cushion assembly.
  4. Connect the RH rear seat recliner switch connector.
  5. Install the bolts (x2) that attach the recliner switch assembly to the seat cushion foam.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
  6. Install the 2nd row seat cushion. See 2ND ROW SEAT CUSHION (Remove and Replace).