2026-04-09

Center Console - Sliding Bin Lid (Remove and Replace)

Correction code 1519020902 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-04-09: Added front side panel steps, floor mat steps and steps of the screw securing the sliding door assembly.

Torque Specifications

Table 1. Torque Specifications: Center Console - Sliding Bin Lid (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x12) that attach the sliding door assembly to the center console
1.2 Nm (.9 lbs-ft)
  • Torx T20 socket
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
 Reuse
Screw that attaches the sliding door assembly to the center console
1.5 Nm (1.1 lbs-ft)
  • Torx T10 bit
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
 Reuse

Remove

  1. Remove the center console rear end panel. See Console - End Panel (Remove and Replace).
  2. Remove the center console LH and RH rear side panels. See Side Panel - Rear - Center Console - LH (Remove and Replace).
  3. Remove the LH and RH floor mats.
  4. Remove the LH and RH front side panels. See Side Panel - Front - Center Console - LH (Remove and Replace).
  5. Remove the phone dock surround. See Surround - Phone Dock - Center Console (Remove and Replace).
  6. Remove the LH and RH hockey sticks. See Hockey Stick - Center Console - LH (Remove and Replace).
  7. Remove the center console phone dock and inductive charger module assembly. See Phone Dock - Center Console (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not separate the phone dock and the inductive charger module.
  8. Remove the center console top face panel. See Panel - Top Face - Center Console (Remove and Replace).
  9. Remove the screws (x12) that attach the sliding door assembly to the center console.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  10. Remove the screw that attaches the sliding door assembly to the center console.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  11. Disconnect the harness connector, and then release the clips (x6) to remove the sliding door assembly from the center console.

Install

  1. Connect the harness connector, and then install the clips (x6) that attach the sliding door assembly to the center console.
  2. Install the screw that attaches the sliding door assembly to the center console.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  3. Install the screws (x12) that attach the sliding door assembly to the center console.
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  4. Install the center console top face panel. See Panel - Top Face - Center Console (Remove and Replace).
  5. Install the center console phone dock and inductive charger module assembly. See Phone Dock - Center Console (Remove and Replace).
  6. Install the LH and RH hockey sticks. See Hockey Stick - Center Console - LH (Remove and Replace).
  7. Install the phone dock surround. See Surround - Phone Dock - Center Console (Remove and Replace).
  8. Install the LH and RH front side panels. See Side Panel - Front - Center Console - LH (Remove and Replace).
  9. Install the center console LH and RH rear side panels. See Side Panel - Rear - Center Console - LH (Remove and Replace).
  10. Install the LH and RH floor mats.
  11. Install the center console rear end panel. See Console - End Panel (Remove and Replace).