2025-03-12

FRONT HEADLINER (Remove and Install)

Correction code 1520010301 FRT 0.00 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: FRONT HEADLINER (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Coat hook screw
2.5 Nm (1.8 lbs-ft)
  • 2 in extension
  • Torx T25 bit
  • Ratchet/torque wrench
  • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
Reuse
Screw that attaches the LH front headliner to the body tether
2 Nm (1.5 lbs-ft)
  • Torx T30 bit
  • Ratchet/torque wrench
  • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
Reuse

Remove

  1. Remove the LH and RH upper A-pillar trims. See Trim - A-Pillar - Upper - LH (Remove and Replace).
  2. Remove the LH and RH sun visors. See SUN VISOR - LEFT HAND (Remove and Replace).
  3. Remove the LH and RH lower A-pillar trims. See A PILLAR LOWER TRIM - LEFT HAND (Remove and Install).
  4. Remove the LH and RH lower C-pillar trims. See Trim - C-Pillar - Lower - LH (5-Seat) (Remove and Replace).
  5. Remove the LH and RH upper B-pillar trims. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  6. Remove the front trunk load floor. See TRUNK LOAD FLOOR - FRONT (Remove and Replace).
  7. Remove the trunk sill trim. See TRUNK SILL LOWER TRIM (Remove and Replace).
  8. Remove the LH and RH trunk rucket brackets. See RUCKET BRACKET - LEFT HAND (Remove and Replace).
  9. Remove the LH and RH upper C-pillar trims. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  10. Remove the rear headliner panel. See REAR HEADLINER (Remove and Replace).
  11. Push open the LH coat hook.
  12. Open the LH coat hook screw cover.
  13. Remove the LH coat hook screw.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 2 in extension
    • Torx T25 bit
    • Ratchet/torque wrench
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
  14. Partially release the LH headliner, and then remove the screw that attaches the LH front headliner to the body tether.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 bit
    • Ratchet/torque wrench
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
  15. Repeat step 11 to 14 to the RH side.
  16. Tilt both front seats rearward to allow headliner removal.
  17. Release the headliner harness clips (x7) and disconnect the electrical connector to release the headliner harness from the LH A-pillar area.
  18. Release the clips (x7), high retention clips (x2) and tabs (x2) that attach the front headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Pliers Needle nose long bent
    • Clip pry tool
  19. With assistance, remove the front headliner from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    First push the headliner with its opening towards the C-pillar, and then rotate it and move it out of the vehicle.

Install

  1. With assistance, position the front headliner into vehicle for installation
    Informational PurposesAn informational icon, calling your attention
    Note
    First push the headliner with its opening towards the C-pillar, and then rotate it and move it into the vehicle.
  2. Align the location pins (x3) on the front headliner to the slots on the body, and then secure the clips (x7), high retention clips (x2) and tabs (x2) that attach the front headliner to the body.
  3. Install the screws (x2) that attach the LH and RH sides of the front headliner to the body tether.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 bit
    • Ratchet/torque wrench
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
    Figure 1. LH Shown, RH Similar
  4. Connect the electrical connector, and then secure the headliner harness clips (x7) to install the headliner harness to the LH A-pillar area.
  5. Install the LH coat hook screw.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 2 in extension
    • Torx T25 bit
    • Ratchet/torque wrench
    • Wurth ¼ in hexagon 1 Nm - 5 Nm torque wrench (installation only)
  6. Close the LH coat hook screw cover.
  7. Push the LH coat hook closed.
  8. Repeat step 5 to 7 for the RH side.
  9. Install the rear headliner panel. See REAR HEADLINER (Remove and Replace).
  10. Install the LH and RH upper C-pillar trims. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  11. Install the LH and RH trunk rucket brackets. See RUCKET BRACKET - LEFT HAND (Remove and Replace).
  12. Install the trunk sill trim. See TRUNK SILL LOWER TRIM (Remove and Replace).
  13. Install the front trunk load floor. See TRUNK LOAD FLOOR - FRONT (Remove and Replace).
  14. Install the LH and RH upper B-pillar trims. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  15. Install the LH and RH lower C-pillar trims. See Trim - C-Pillar - Lower - LH (5-Seat) (Remove and Replace).
  16. Install the LH and RH lower A-pillar trims. See A PILLAR LOWER TRIM - LEFT HAND (Remove and Install).
  17. Install the LH and RH sun visors. See SUN VISOR - LEFT HAND (Remove and Replace).
  18. Install the LH and RH upper A-pillar trims. See Trim - A-Pillar - Upper - LH (Remove and Replace).