2026-05-21

Brake Pad Kit - Rear (Remove and Replace)

Correction code 3301020302 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-05-21: Removed instruction to apply brake grease. Added note advising against applying brake grease.
  • 2026-02-16: Released new procedure.
Equipment:
  • 1082171-10-A/1082171-00-A - S-hook
  • 1109954-00-A - KIT, BASE CALIPER SPREADER
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
Informational PurposesAn informational icon, calling your attention
Note
Dispose of used brake fluid in a manner consistent with local environmental codes.

Torque Specifications

Table 1. Torque Specifications: Brake Pad Kit - Rear (Remove and Install), Brake Pad Kit - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH rear brake caliper to the LH rear brake caliper bracket
26.5 Nm (19.5 lbs-ft)
  • 14 mm socket
  • Flex head ratchet/flex head torque wrench
  • Combination Wrench 12pt 17mm
 Reuse
Performance models: bolt that attaches the rear caliper logo plate to the brake caliper
9 Nm (6.6 lbs-ft)
  • 5 mm hex
  • Flex head ratchet/flex head torque wrench
 Reuse

Remove

  1. Put the vehicle on a 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Make sure that the vehicle is not charging.
  2. Open the LH front door and lower the window.
  3. Enable the EPB Service Mode.
    1. Enable Service Mode. See Service Mode.
    2. Unlock the vehicle gateway. See Gateway (Unlock).
    3. While holding the brake pedal, tap the Service Mode "wrench" at the bottom of the touchscreen UI, and then tap Chassis > Brakes > EPB Service Mode, select Both in the EPB Selection drop down list, and select Start in the Action Selection drop down list. Click Run, and allow the routine to complete.
  4. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  5. Put absorbent material underneath the brake fluid reservoir area.
  6. Clean the area around the brake fluid reservoir and remove the brake reservoir cap.
  7. Remove the LH and RH rear wheels. See Wheel Assembly (Remove and Install).
  8. Performance models only: remove the bolt that attaches the rear caliper logo plate to the rear caliper.
  9. Remove the bolts (x2) that attach the LH rear brake caliper to the LH rear brake caliper bracket.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 14 mm socket
    • Flex head ratchet/flex head torque wrench
    • Combination Wrench 12pt 17mm
  10. Use the Brake Caliper Spreader to push the piston into the caliper.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the up cut of the piston is placed in the middle of the two tabs.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 1109954-00-A - KIT, BASE CALIPER SPREADER
  11. Remove the LH rear brake caliper and hang it off to a firm part beside with an S-hook.
    Informational PurposesAn informational icon, calling your attention
    Note
    Preferentially use S-hook 1082171-10-A. If 1082171-10-A is not available, use 1082171-00-A instead.
    Informational PurposesAn informational icon, calling your attention
    Note
    S-hook 1082171-10-A can only be hung on metal parts.
  12. Remove the LH rear brake pads from the LH rear brake caliper bracket.
  13. Remove the LH rear brake caliper bracket abutment clips (x4).
  14. Clean the LH rear brake caliper bracket and the abutment clips with soapy water or brake cleaner.
  15. Repeat steps 8 through 14 on the RH side of the vehicle.

Install

Informational PurposesAn informational icon, calling your attention
Note
Do not apply brake grease to the brake pad or brake caliper. 2025+ Model Y brakes do not require the application of brake grease.
  1. Install the LH rear brake caliper bracket abutment clips (x4).
  2. Remove the protective film from the double sided tape on the LH rear brake pads.
  3. Install the LH rear brake pads onto the LH rear brake caliper bracket.
  4. Install the bolts (x2) that attach the LH rear brake caliper to the LH rear brake caliper bracket.
    26.5 Nm (19.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 14 mm socket
    • Flex head ratchet/flex head torque wrench
    • Combination Wrench 12pt 17mm
  5. Performance models only: install the bolt that attaches the rear caliper logo plate to the rear caliper.
    9 Nm (6.6 lbs-ft)
    Use of the following tool(s) is recommended:
    • 5 mm hex
    • Flex head ratchet/flex head torque wrench
  6. Repeat steps 1 through 5 for the RH side of the vehicle.
  7. Lower the vehicle to a comfortable working height and set the lift onto locks.
  8. Check the brake fluid reservoir and top off as necessary.
  9. Remove the absorbent material from underneath the brake fluid reservoir area.
  10. Pump the brake pedal 3-5 times to seat the pads against the brake rotor until the brake pedal feels firm.
  11. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Chassis > Brakes > EPB Service Mode, select Both in the EPB Selection dropping list, and select Stop in the Action Selection dropping list. Click Run, and allow the routine to complete.
  12. Exit Service Mode. See Service Mode.
  13. Install the LH and RH rear wheels. See Wheel Assembly (Remove and Install).
  14. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  15. Perform the brake pad burnishing procedure. See Brake Pads - Burnishing
    Informational PurposesAn informational icon, calling your attention
    Note
    Add the correction code for brake pad burnishing 33013000 as a separate activity to the Service Visit.