2026-07-01

Lower Trunk (Remove and Replace)

Correction code 1010060102 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-06-05: Updated fastener information.

Torque Specifications

Table 1. Torque Specifications:Lower Trunk (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x5) that attach the rear diffuser to the lower trunk assembly
5 Nm (3.7 lbs-ft)
10 mm deep socket Reuse
Lower trunk assembly rear center bolt
10 Nm (7.4 lbs-ft)
  • 10 mm socket
 Replace 1784125-00-A
Bolts (x4) that attach the lower trunk assembly to the vehicle
24 Nm (17.7 lbs-ft)
  • 13 mm socket
 Reuse

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2-Post Lift
  2. Use a small flat head screwdriver to open the fastener covers (x2), and then remove the bolts (x5) that attach the rear diffuser to the lower trunk assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • 4 in extension
    • Cordless Ratchet/Impact Driver
  3. Lower the vehicle to a comfortable working height, and then lower the lift until the safety locks are properly engaged.
  4. Remove the trunk tub. See Trunk Tub (Remove and Replace).
  5. Remove the bottom foam pad from the lower trunk.
  6. Remove and discard the rear center bolt from the lower trunk assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Remove the bolts (x4) that attach the lower trunk assembly to the vehicle, and then remove the lower trunk assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket

Install

  1. Install the bolts (x4) that attach the lower trunk assembly to the vehicle.
    24 Nm (17.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  2. Install a new rear center bolt to the lower trunk assembly.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the bottom foam pad to the lower trunk.
  4. Install the trunk tub. See Trunk Tub (Remove and Replace).
  5. Raise the vehicle, and then lower the lift until the safety locks are properly engaged.
  6. Install the bolts (x5) that attach the rear diffuser to the lower trunk assembly, and close the fastener covers (x2) .
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • 4 in extension
    • Cordless Ratchet/Impact Driver
    • Torque wrench with angle measurement
  7. Lower the vehicle fully, and remove the lift arms from under the vehicle.