Correction code TBD FRT 2.04 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

1. Open all four doors

   

2. Lower all four windows

   

3. Move LH front seat forward
   Note

   Adjust seat back if needed to avoid contacting headliner

   

4. Move RH front seat forward
   Note

   Adjust seatback if needed to avoid contacting headliner

   

5. Move 60 seat to easy entry position
   Note

   Press shoulder switch then push seat forward

   

   

6. Partially remove lower portion of LH rear door seal

   

7. Remove LH 7s lower C-pillar trim
   Note

   8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips

   

   

8. Move 60 seat to original position
   Note

   Press shoulder switch then pull seat backward

   

9. Fold 2nd row 60 seatback down
   Note

   Via seat switch or manual tether, Protect seat back upholstery if necessary

   

   

10. Disconnect 2nd row 60 seat connector
    Note

    1x connector,

    

    

11. Move 60 seat forward using towel bar
    Note

    With one hand on towel bar pull up and slide the seat forward with your other hand

    

    

12. Remove 60 seat rear outboard track fastener
    Note

    1x patch bolt, 11mm, 37 Nm, Discard after removal

    

13. Remove 60 seat rear inboard track fasteners
    Note

    2x patch bolts, 11mm, 37 Nm, Discard after removal

    

14. Move 60 seat fully rearward using towel bar
    Note

    pull up bar, slide seat forward

    

15. Remove 60 seat outboard track cover
    Note

    1x clip, Slide covers forward to release from 60 seat tracks

    

    

    

16. Remove center track cover from 2nd row seats
    Note

    2x clips, Slide covers forward to release from 2nd row seat tracks

    

    

    

17. Release cabin carpet from 60 seat
    Note

    Pull cabin carpet towards front of vehicle

    

    

18. Remove 60 seat front inboard track fasteners
    Note

    1x bolts, 11mm, 37 Nm, Discard after removal

    

19. Remove 2nd row 60 seat frame front outboard track fasteners
    Note

    1x bolts, 11mm, 37 Nm, Discard after removal

    

20. Remove 2nd row 60 seat assembly from vehicle
    Note

    Recommend assistance, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement

    

    

21. Move RH front seat forward
    Note

    Adjust seatback if needed to avoid contacting headliner

    

22. Move 60 seat to easy entry position
    Note

    Press shoulder switch then push seat forward

    

    

23. Partially remove RH rear door seal
    Note

    Pillar and sill trim have tabs seated underneath seal

    

24. Remove RH C-pillar lower trim
    Note

    5x clips, Rear edge is mated with groove in trunk side trim, Release clips at front of LH Lower C-Pillar trim working your way back towards rear of sill trim, trim part may slightly differ by vehicle build location, and the number of clips may also varyt, by vehicle build location, Confirm each installation with push-pull test, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly, if clip position is changed or push-pull action shows bracket not secure, remove clip from tab and seat clip into doghouse on bracket and reinstall

    

    

25. Move 40 seat to original position
    Note

    Press shoulder switch then pull seat backward

    

26. Fold 2nd row 40 seatback down
    Note

    Via seat switch or manual tether, Protect seat back upholstery if necessary

    

    

27. Remove 40 seat outboard track cover
    Note

    1x clip, Slide cover forward to release from 40 seat track

    

28. Remove bolts securing 40 seat podium to vehicle
    Note

    2x patch bolts, 11mm, 37 Nm, Discard bolts after removal

    

29. Move 40 seat forward using towel bar
    Note

    With one hand on towel bar pull up and slide the seat forward with your other hand

    

30. Remove bolts securing 40 seat inner and outer tracks to vehicle
    Note

    2x patch bolts, 11mm, 37 Nm, Discard bolts after removal

    

31. Move 40 seat fully rearward using towel bar
    Note

    pull bar, slide seat forward

    

32. Disconnect 2nd row 40 seat connector
    Note

    1x connector, Newer models may have red locking tab

    

    

33. Remove 40 seat from vehicle
    Note

    Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement

    

    

34. Remove 3rd row seat cushion
    Note

    2x clips, 1x connector, 2x circular hooks, Press tabs backward then pull front edge up, Press rear seat cushion and lift the front seat cushion

    

    

    

    

    

35. Remove 3rd row LH seat cushion bolster
    Note

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster towards front of vehicle to remove

    

36. Remove 3rd row RH seat cushion bolster
    Note

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster towards front of vehicle to remove

    

    

    

37. Release LH side of 3rd row rear carpet
    Note

    2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Remove bolt then release carpet

    

    

    

    

38. Release RH side of 3rd row rear carpet
    Note

    2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Remove bolt then release carpet

    

    

    

    

39. Remove 3rd row rear cabin carpet

    

    

40. Open hood

    

    

41. Power off vehicle from center display
    Note

    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box

    

    

42. Remove rear apron
    Note

    16x trim clips, 3x datums, 2x clips

    

    

    

    

43. Remove HEPA filter assembly
    Note

    2x bolts, 10mm, 10 Nm, Pivot rear edge up past brake reservoir then lift up to clear frunk assembly

    

    

    

    

44. Disconnect LV battery and first responder loop
    Note

    2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

    

    

    

45. Verify operation of multimeter
    Note

    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing the 16v battery

    

46. Remove 3rd row NVH insulator
    Note

    1x connector, Disconnect connector then remove insulator

    

    

    

    

47. Install HVC logic cap
    Note

    1x logic cap

    

48. Remove all items from pockets and ensure not wearing metal items

    

49. Inspect HV insulating gloves
    Note

    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves. https://service.teslamotors.com/documents?model=&keys=TN-15-92-003&vehicle_system=&sort_by=field_date_submitted&sort_order=DESC

    

50. Put on HV insulating gloves and leather over gloves
    Note

    Use HV cut resistant insulated gloves or HV insulating gloves and leather over gloves, HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used, Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration.

    

51. Release positive LV output cover from PCS cable
    Note

    1x cover

    

    

52. Remove PCS cable from LV passthrough output
    Note

    1x nut, 13mm, 9 Nm, Discard nut after removal

    

53. Remove bolts securing ancillary bay probe lid cover
    Note

    2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal

    

54. Remove ancillary bay probe lid cover

    

    

55. Verify no high voltage
    Note

    Make sure to wear PPE (HV gloves, Safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

56. Wipe ancillary bay cover with IPA to clean surface
    Note

    Allow to 1 minute dry time

    

57. Inspect ancillary bay probe lid cover gasket then position onto ancillary bay cover
    Note

    Confirm no visual damage present, Wipe ancillary bay with IPA to clean surface, Allow to 1 minute dry time

    

    

58. Install bolts securing ancillary bay probe lid cover to ancillary bay cover
    Note

    2x bolts, EP10 5-Lobe, 6 Nm, Install new bolts

    

59. Remove bolts securing ancillary bay cover to HVC
    Note

    3x bolts, E10, 5 Nm + 30 degrees

    

60. Remove bolts securing ancillary bay cover to HV battery
    Note

    18x bolts, E10 5-Lobe, 8 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the ancillary bay cover

    

    

61. Remove HVC logic cap
    Note

    1x logic cap

    

62. Remove ancillary bay cover from HV battery

    

    

63. Install HVC logic cap
    Note

    1x logic cap

    

64. Inspect ancillary bay for any missing insulators
    Note

    Install service insulator kit before continuing to next step

    

    

    

    

    

65. Remove bolts securing pyro disconnect to ancillary bay
    Note

    1x insulator, 2x patch bolts, 13mm, 9 Nm, Discard after removal

    

    

66. Remove pyro disconnect from ancillary bay
    Note

    1x connector, From the bottom, Lift pyro disconnect straight up and out of the ancillary bay

    

    

67. Install pyro disconnect dummy

    

68. Disconnect AC harness connector from PCS
    Note

    1x connector, Release the locking tab by pulling upward, May need plastic trim tool to help lift the connector upward

    

69. Remove AC Filter harness
    Note

    1x connector, 1x clip, 2x bolts, 8mm, 4.5 Nm, Pass harness under PCS hose, Release red locking tab, Discard bolts after removal

    

    

    

    

    

70. Remove ancillary bay left terminals cover
    Note

    2x tabs, 1x datum

    

    

71. Disconnect LV fastcharge contactor connector
    Note

    1x connector, Press tabs on both sides by hand and disconnect the connector upwards

    

72. Disconnect mega harness connector from DC input assembly
    Note

    1x connector

    

73. Remove ancillary bay harness clip around negative pack contactor area
    Note

    3x clip

    

74. Remove insulator for DC input assembly to both fastcharge busbar inlet side
    Note

    3x insulators

    

75. Remove bolt securing negative fastcharge busbar inlet side and negative DC input assembly busbar
    Note

    1x patch bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal

    

76. Remove bolt securing positive fastcharge busbar inlet side and positive DC input assembly busbar
    Note

    1x patch bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal

    

77. Remove bolts securing FC assembly to ancillary bay
    Note

    2x bolts, 10mm, 5.5 Nm

    

78. Remove fastener securing busbar cover access door
    Note

    1x bolt, 10mm, 9 Nm

    

79. Remove bolts securing charge port busbar kit to HV header
    Note

    2x bolts, 10mm, 9 Nm

    

80. Release LH body harness from rear body and move aside
    Note

    1x clip

    

81. Partially remove LH B-pillar lower trim
    Note

    1x push clip

    

    

82. Partially pull out LH rear body harness

    

83. Lift busbar kit connector to remove from HV header
    Note

    Use inflatable air bag to suspend busbar away from HV header during removal and installation, hold busbar firmly as there is tension on, Avoid damaging the harness bracket

    

84. Remove bolts securing busbar DC input assembly to ancillary bay
    Note

    4x bolts, EP10 5-Lobe, 10 Nm, Discard after removal

    

    

85. Remove Busbar DC input assembly from ancillary bay

    

    

86. Remove FC assembly from ancillary bay
    Note

    2x guide pins

    

    

    

87. Remove and discard FC insulator cover from FC assembly
    Note

    8x clips, 1x alignment pin

    

    

    

88. Remove DC link positive busbar from fastcharge contactor
    Note

    2x location pins, 1x patch bolt, 13mm, 10 Nm, Minus 180 degress, 10 Nm, Discard after removal

    

    

89. Remove DC link negative busbar from fastcharge contactor
    Note

    2x location pins, 1x patch bolt, 13mm, 10 Nm, Minus 180 degress, 10 Nm, Discard after removal

    

    

90. Remove busbar fastcharge input negative from fastcharge contactor
    Note

    2x tabs, 3x location pins, 1x patch bolt, 13mm, 10 Nm, Minus 180 degress, 10 Nm, Discard after removal

    

    

91. Remove the positive inlet fastcharge busbar from fastcharge contactor
    Note

    1x patch bolt, 13mm, 9 Nm, Discard after removal, 0300_001

    

    

92. Remove fastcharge contactor from lower fastcharge insulator assembly
    Note

    3x bolts, E8, 5.5 Nm, 2x guides

    

    

93. Install the fastcharge contactor to lower fastcharge assembly insulator
    Note

    2x guides, Align the guides, 3x bolts, E8, 5.5 Nm, Mark after torque

    

    

    

94. Install positive inlet fastcharge busbar to fastcharge contactor
    Note

    1x patch bolt, 13mm, 9 Nm Mark after torque, Install new patch bolt

    

95. Remove DC link positive busbar from fastcharge contactor
    Note

    2x location pins, 1x patch bolt, 13mm, 10 Nm, Minus 180 degress, 10 Nm, Discard after removal

    

    

96. Perform Hioki impedance test at the negative HV joints of the fastcharge contactor on DC link busbar and inlet busbar
    Note

    2x HV joints, Functional specification 40μΩ or less, Hioki 9461 specification not available

    

    

97. Install busbar fastcharge input negative to fastcharge contactor
    Note

    2x tabs, 3x location pins, 1x patch bolt, 13mm, 10 Nm, Minus 180 degress, 10 Nm, Install new patch bolt, Mark after torque

    

    

98. Install DC link negative busbar to fastcharge contactor
    Note

    2x location pins, 1x patch bolt, 13mm, 10 Nm, Minus 180 degrees, 10 Nm, Install new patch bolt, Mark after torque

    

    

99. Perform Hioki impedance test at the positive HV joints of the fastcharge contactor on DC link busbar and inlet busbar
    Note

    2x HV joints, Functional specification 30μΩ or less, Hioki 9461 specification not available

    

    

100. Install new FC insulator cover to FC assembly
     Note

     8x clips, 1x alignment pin

     

     

     

     

101. Position FC assembly to ancillary bay for installation
     Note

     2x guide pins

     

     

     

102. Install bolts securing FC assembly to ancillary bay
     Note

     2x bolts, 10mm, 5.5 Nm, Mark after torque

     

103. Install Busbar DC input assembly to ancillary bay
     Note

     Ensure seal is not damaged and seated properly

     

     

104. Install bolts securing Busbar DC input assembly to ancillary bay
     Note

     4x bolts, EP10 5-Lobe, 10 Nm, Install new bolts, Mark after torque

     

     

     

105. Install and torque bolt securing negative fastcharge busbar inlet
     Note

     1x patch bolt, 13mm, 15 Nm, Minus 180 degrees, 5Nm + 60 degrees, Install new patch bolt, Mark after torque

     

106. Install and torque bolt securing positive fastcharge busbar inlet
     Note

     1x patch bolt, 13mm, 15 Nm, Minus 180 degrees, 5Nm + 60 degrees, Install new patch bolt, Mark after torque

     

107. Perform Hioki resistance test at both HV joints of DC input assembly busbar
     Note

     2x HV joints, 60μΩ or less, Test from negative fastcharge busbar to negative DC input busbar and positive fastcharge busbar to positive DC input busbar

     

     

     

     

108. Install insulator for DC input assembly to both fastcharge busbars inlet side
     Note

     3x insulators

     

109. Connect mega harness connector to DC input assembly
     Note

     1x connector

     

110. Install and torque bolt negative fastcharge busbar
     Note

     1x patch bolt, 13mm, 15 Nm, Minus 180 degrees, 5Nm + 60 degrees, Install new patch bolt, Mark after torque

     

111. Perform Hioki impedance test negative HV joint fastcharge busbar DC link side
     Note

     1x HV joint, 55μΩ or less

     

     

112. Install and torque bolt securing positive fastcharge busbar
     Note

     1x patch bolt, 13mm, 15 Nm, Minus 180 degrees, 5Nm + 60 degrees, Install new patch bolt, Mark after torque

     

113. Perform Hioki impedance test positive HV joint fastcharge busbar DC link side
     Note

     1x HV joint, 25μΩ or less

     

     

114. Install ancillary bay left terminals cover
     Note

     2x tabs, 1x datum

     

     

115. Install harness clips to FC contactor cover
     Note

     2x clips

     

116. Install ancillary bay harness clip around negative pack contactor area
     Note

     1x clip

     

117. Connect LV fastcharge connector
     Note

     1x connector, Secure locking tab, 1x harness clip

     

118. Connect mega harness connector to DC input assembly
     Note

     1x connector

     

119. Install AC filter harness
     Note

     1x connector, 1x clip, 2x bolts, 8mm, 4.5 Nm, Pass harness under PCS hose, Press down on red locking tab, Install new bolts

     

     

     

     

     

120. Clean HV connector contact surface of residual Penetrox
     Note

     Allow 1 minute dry time, New busbar comes with penetrox applied to HV connector

     

121. Clean busbar HV connector contact surface of residual Penetrox
     Note

     Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

     

122. Apply Penetrox onto HV connector joints
     Note

     Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

     

     

123. Remove inflatable air bag from under HV header

     

124. Position busbar kit connector and lower onto HV header
     Note

     Shift rear end of busbar assembly upward to help ease installation, If excessive force is required to seat busbars, they may have been bent. Inspect for damage and replace if necessary

     

125. Install bolts securing charge port busbar kit to HV header
     Note

     2x bolts, 10mm, 9 Nm, Mark after torque

     

126. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
     Note

     2x HV joints, The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ). If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session. If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again. If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), Hioki test passed, proceed to next step

     

     

127. Install fastener securing busbar cover access door
     Note

     1x bolt, 10mm, 9 Nm

     

128. Position LH rear body harness under LH lower C pillar trim

     

129. Install LH body harness onto rear body
     Note

     1x clip

     

130. Partially install LH B-pillar lower trim
     Note

     1x push clip

     

131. Partially install lower portion of LH C-pillar trim

     

132. Remove pyro disconnect dummy

     

133. Clean mating surface of pyro
     Note

     Allow to 1 minute dry time, Use an IPA wipe to clean the HV mating surfaces of the shunt, Busbar, And the pyrotechnic battery disconnect

     

     

     

134. Set multimeter to "LoZ" (low impedance) mode

     

135. Measure voltage between busbar and shunt
     Note

     Measure the voltage between the busbar (left) and shunt (right) for at least 10 seconds, so as to balance the voltage across the pyrotechnic battery disconnect mount points, Note: The voltage displayed on the multimeter is not as important as balancing the mount points

     

     

136. Position pyro disconnect to ancillary bay for installation
     Note

     1x connector, While still measuring the voltage, Have an assistant position the pyrotechnic battery disconnect into the HV battery for installation. Make sure to align the pins of the connector with the new pyrotechnic battery disconnect, And then press the pyrotechnic battery disconnect down onto the busbars, The pyro disconnect can only be installed one way

     

     

     

     

137. Install bolts securing pyro disconnect to ancillary bay
     Note

     2x patch bolts, 13mm, 9 Nm, Install new patch bolt, Mark with paint pen

     

138. Measure resistance from module 2 busbar to pyro disconnect
     Note

     1x HV joint, 60μΩ or less, Perform zero adjust to Hioki meter prior to testing

     

     

139. Measure resistance from pyro disconnect to shunt
     Note

     1x HV joint, 45μΩ or less, Perform zero adjust to Hioki meter prior to testing

     

     

140. Remove service insulator kit

     

     

     

     

141. Remove HVC logic cap
     Note

     1x logic cap

     

142. Inspect ancillary bay walls for damage
     Note

     Any dent or depression in the sealing surface that causes it to not be flat will result in a leak, Any paint that comes off the ancillary bay wall, Whether or not it sticks to the seal, Will require enclosure leak test when reassembled, It can still be reused

     

143. Inspect ancillary bay cover seal to confirm it has no visual damage
     Note

     Image up close for clarity, Delaminated and torn seals cannot be reused

     

     

     

     

     

144. Wipe ancillary bay cover with IPA to clean surface
     Note

     Allow to 1 minute dry time

     

145. Position ancillary bay cover to HV battery for installation
     Note

     Ensure all accessible insulators are present, Wearing Electrical Protective Gloves is not necessary once all HV components are covered.

     

     

146. Remove leather over gloves and HV insulating gloves

     

147. Install bolts securing ancillary bay cover to HV battery
     Note

     18x bolts, EP10 5-Lobe, 8 Nm, Fasteners are captive, Follow torque sequence per image

     

     

148. Install bolts securing ancillary bay cover to HVC
     Note

     3x bolts, E10, 5 Nm + 30 degrees

     

149. Install positive LV output from PCS cable and torque nut securing it
     Note

     1x nut, 13mm, 9 Nm, Install new nut, Mark the nut after torque

     

150. Install positive LV output cover to PCS cable
     Note

     1x cover

     

151. Remove HVC logic cap
     Note

     1x logic cap

     

152. Install 3rd row NVH insulator
     Note

     1x connector, Install insulator then connect connector

     

     

     

     

153. Position 3rd row rear cabin carpet

     

     

154. Secure RH side of 3rd row rear carpet
     Note

     2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Secure carpet then install bolt

     

     

     

     

155. Secure LH side of 3rd row rear carpet
     Note

     2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Secure carpet then install bolt

     

     

     

     

156. Install 3rd row LH seat cushion bolster
     Note

     1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster into seat frame complete

     

     

157. Install 3rd row RH seat cushion bolster
     Note

     1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster into seat frame complete

     

     

     

158. Install 3rd row seat cushion and connect harness
     Note

     1x connector, Secure 3rd row seat cushion into RH and LH latches

     

     

159. Connect first responder loop and LV battery
     Note

     2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

     

     

     

     

     

160. Install HEPA filter assembly
     Note

     2x bolts, 10mm, 10 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct, Do not pinch washer hose inbetween HEPA filter assembly and body

     

     

     

     

     

     

161. Install rear apron
     Note

     16x trim clips, 3x locator pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron

     

     

     

162. Close hood

     

     

163. Install 40 seat into vehicle
     Note

     Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium

     

     

164. Connect 2nd row 40 seat connector
     Note

     1x connector,

     

     

165. Install bolts securing 40 seat podium to vehicle hand tight
     Note

     2x patch bolts, 11mm, 37 Nm, Install new bolts, Torque at later step

     

166. Move 40 seat forward using towel bar
     Note

     pull up bar, slide seat forward

     

167. Install bolts securing 40 seat inner and outer tracks to vehicle
     Note

     2x patch bolts, 11mm, 37 Nm, Install new bolts

     

168. Move 40 seat to original position
     Note

     Press shoulder switch then pull seat backward

     

169. Install cabin carpet to 40 seat

     

170. Torque bolts securing 40 seat podium to vehicle
     Note

     2x patch bolts, 11mm, 37 Nm

     

171. Install center track cover to 2nd row seats
     Note

     2x clip, Slide cover straight on to clip to 2nd row seat tracks

     

     

     

172. Install 40 seat outboard track cover
     Note

     1x clip

     

173. Position 40 seat into easy entry mode
     Note

     Press shoulder switch and push 40 seat forward

     

     

174. Install RH rear sill trim
     Note

     4x tabs, 3x clips, 5x location pins, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips

     

     

175. Reseat RH rear door seal
     Note

     Seat pillar and sill trim tabs underneath seal

     

176. Move 40 seat to original position
     Note

     Press shoulder switch then pull seat backward

     

177. Move RH front seat to original position

     

178. Install 2nd row 60 seat assembly
     Note

     Recommend assistance

     

     

     

179. Connect 2nd row 60 seat connector
     Note

     1x connector,

     

     

180. Install fasteners securing 60 seat frame to body
     Note

     5x patch bolts, 11mm, 37 Nm, Install new patch bolts, bottom seat bolts located in rear

     

     

     

     

181. Secure cabin carpet to 60 seat
     Note

     Strap velcro on

     

     

182. Return 2nd row 60 seatback to vertical position
     Note

     Via trunk seat switch, Remove seatback protection if necessary

     

     

183. Install 60 seat outboard track cover
     Note

     1x clip

     

     

     

184. Position 60 seat into easy entry mode
     Note

     Press shoulder switch and push 60 seat forward to position into easy entry mode

     

     

185. Install LH 7s lower C-pillar trim
     Note

     8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips

     

     

186. Reseat LH rear door seal
     Note

     Seat pillar and sill trim tabs underneath seal

     

187. Move 60 seat to original position

     

188. Move RH front seat to original position

     

189. Move LH front seat to original position

     

190. Raise all four windows
     Note

     Via LH front door switch

     

191. Run ODIN routine PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
192. Unlock the vehicle gateway. See Gateway (Unlock).
193. Run ODIN routine PROC_VCLEFT_X_2R-SEAT-RECLINE-CALIBRATIONvia Service Mode:Low Voltage ➜ Second Row Seats ➜ Calibratevia Toolbox:(link)
194. Run ODIN routine PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
195. Close all four doors
     Note

     If LV is powered up then unlatch rear doors before closing