2025-03-12

1ST ROW TILT MOTOR (Remove and Replace)

Correction code 1301020902 FRT 0.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Torque Specifications

Table 1. Torque Specifications: 1ST ROW TILT MOTOR (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x3) that attach the tilt motor to the seat frame
7.5 Nm (5.5 lbs-ft)
  • Ratchet/torque wrench
  • 8 mm 12-point deep socket
Reuse
Bolt that attaches the driver seat tilt motor adjustment arm to the seat assembly
16 Nm (11.8 lbs-ft)
  • Ratchet/torque wrench
  • Torx T40 socket
Replace 1109741-00-E

Remove

  1. Remove the outboard side shield. See 1ST ROW OUTBOARD SIDESHIELD - FOR LEFT HAND SEAT - LUMBAR (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the seat cushion button switch, the recliner button switch and the 8 way switch.
  2. Disconnect the electrical harness from the tilt motor connector.
  3. Remove the bolts (x3) that attach the tilt motor to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not remove the adjustment arm bolt at this time.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 8 mm 12-point deep socket
  4. Remove and discard the bolt that attaches the driver seat tilt motor adjustment arm to the seat assembly, and then remove the tilt motor from the seat frame.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx T40 socket

Install

  1. Position the tilt motor to the seat frame for installation.
    Informational PurposesAn informational icon, calling your attention
    Note
    Hold the tilt motor up and against the seat frame. Ensure the motor alignment pins are visible in the seat frame.
  2. Remove the bolts (x3) that attach the tilt motor to the seat frame.
    7.5 Nm (5.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 8 mm 12-point deep socket
  3. Install a new bolt (1109741-00-E) to attach the driver seat tilt motor adjustment arm to the seat assembly.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Torx T40 socket
  4. Connect the electrical harness to the tilt motor connector.
  5. Install the outboard side shield. See 1ST ROW OUTBOARD SIDESHIELD - FOR LEFT HAND SEAT - LUMBAR (Remove and Replace).
  6. Calibrate the seat by using the touchscreen. Tap Controls > Service > Driver Seat, Steering & Mirrors Calibration > Start, then follow the instructions on the touchscreen, and allow the process to complete.
  7. Move the driver seat to original position.
  8. Raise the LH front window and close the LH front door.