2025-03-12

ASY. FRONT CONTROLLER GEN 3 (Remove and Install)

Correction code 1715010101 FRT 0.35 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Table 1. Torque Specifications: ASY. FRONT CONTROLLER GEN 3 (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the front body controller module cover to the front body controller module
8.5 Nm (6.3 lbs-ft)
  • 10 mm socket
Reuse
Bolts (x2) that attach the harness guide to the front body controller module
6 Nm (4.4 lbs-ft)
  • 8 mm socket
Replace 1137934-00-A
Bolts (x3) that attach the front body controller module to the body
10 Nm (7.4 lbs-ft)
  • 10 mm socket
Reuse
Bolt that attaches the ground strap to the lower right side of the front body controller module
9 Nm (6.6 lbs-ft)
  • 10 mm socket
Reuse

Remove

  1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  2. Disconnect the LV battery. See LV Power (Disconnect and Connect).
  3. Remove the cabin intake duct. See Duct - Air Intake (Remove and Replace).
  4. Release the clip that attaches the supermanifold harness to the front body controller module.
  5. Disconnect the thermal harness from the front body controller module connector.
  6. Remove the bolts (x2) that attach the front body controller module cover to the front body controller module, and then remove the cover.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Disconnect the electrical harness from the front body controller module connectors (x5).
  8. Remove and discard the bolts (x2) that attach the harness guide to the front body controller module.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  9. Pivot the harness guide slightly forward and up to release the clip from the front body controller module.
  10. Remove the bolts (x3) that attach the front body controller module to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Remove the bolt that attaches the ground strap to the lower right side of the front body controller module.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  12. Release the clip that attaches the positive cable to the front body controller.
  13. Remove the front body controller module from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Swing the controller forward and up to release from the top temp set.

Install

  1. Maneuver the front body controller module into position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the module over the hook, and then position into bottom bracket holes.
  2. Install the bolts (x3) that attach the front body controller module to the body.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Pivot the harness guide upward and back to install the clip to the front harness.
  4. Install new bolts (x2) that attach the harness guide to the front body controller module.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  5. Install the bolt that attaches the ground strap to the lower right side of the front body controller module.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  6. Install the clip that attaches the positive cable to the front body controller.
  7. Connect the electrical harness to the front body controller module connectors (x5).
  8. Install the front body controller module cover, and then install the bolts (x2) that attach the front body controller module cover to the front body controller module.
    8.5 Nm (6.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  9. Connect the thermal harness to the front body controller module connector.
  10. Install the clip that attaches the supermanifold harness to the front body controller module.
  11. Connect the LV battery. See LV Power (Disconnect and Connect).
  12. Install the cabin intake duct. See Duct - Air Intake (Remove and Replace).
  13. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).