2025-03-12

SERVICE KIT - SUPERMANIFOLD SOV COIL - HEAT PUMP (Remove and Install)

Correction code 1840010702 FRT 0.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Thermal management components operate under very tight specifications and can malfunction if Service procedures are not carefully followed. DO NOT rely on past experience with other thermal management systems; read through the Service Manual and do not deviate from the instructions.

Remove

  1. Disconnect the LV battery. See LV Power (Disconnect and Connect).
  2. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  3. Release the locking tab, and then disconnect the electrical connector from the high pressure and temperature sensor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  4. Release the locking tab, and then disconnect the electrical connector from the recirc EXV (expansion valve).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  5. Release the locking tab, and then disconnect the electrical connector from the liquid cooled condenser EXV.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  6. Release the locking tab, and then disconnect the electrical connector from the liquid cooled condenser shut off valve.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  7. Release the locking tab, and then disconnect the electrical connector from the right side cabin condenser EXV.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
  8. Move thermal harness from supermanifold to side.
  9. Remove the bolt that attaches the liquid cooled condenser shut off valve coil to the shut off valve core, and then remove the shut off valve coil from vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 3 mm hex

Install

  1. Position the liquid cooled condenser shut off valve coil on the shut off valve core.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align shut off valve coil on the shut off valve core.
  2. Install the bolt that attaches the liquid cooled condenser shut off valve coil to the shut off valve core.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 3 mm hex
  3. Route thermal harness back to supermanifold.
  4. Connect the electrical connector on the right side cabin condenser EXV.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  5. Connect the electrical connector on the liquid cooled condenser shut off valve.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  6. Connect the electrical connector on the liquid cooled condenser EXV.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  7. Connect the electrical connector on the recirc EXV.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  8. Connect the electrical connector on the high pressure and temperature sensor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  9. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  10. Connect the LV battery. See LV Power (Disconnect and Connect).