2025-03-12

EPB HARNESS LEFT HAND (Remove and Replace)

Correction code 3301021102 FRT 0.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: EPB HARNESS LEFT HAND (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH rear EPB harness bracket to the LH rear caliper
5 Nm (3.7 lbs-ft)
  • 4 in extension
  • 10 mm socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
Reuse
Bolt that attaches the LH rear EPB harness to the LH rear brake hose bracket
6 Nm (4.4 lbs-ft)
  • 10 mm deep socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
Reuse

Remove

  1. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  2. Partially release the clips that attach the LH rear wheel liner to body, and then move the wheel liner aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Be careful not to damage the wheel liner.
  3. Disconnect the LH rear EPB caliper connector.
  4. Remove the bolt that attaches the LH rear EPB harness bracket to the LH rear caliper.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 4 in extension
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  5. Remove the bolt that attaches the LH rear EPB harness to the LH rear brake hose bracket.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  6. Release the clips (x2) that attach the LH rear EPB harness to body.
  7. Disconnect the LH rear EPB harness connector and remove the harness.

Install

  1. Connect the LH rear EPB harness connector.
  2. Install the clips (x2) that attach the LH rear EPB harness to body.
  3. Align the locating tab to the brake hose bracket, and then install the bolt that attaches the LH rear EPB harness to the LH rear brake hose bracket.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  4. Install the bolt that attaches the LH rear EPB harness bracket to the LH rear caliper.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 4 in extension
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  5. Connect the LH rear EPB caliper connector.
  6. Re-install the clips that attach the LH rear wheel liner to body.
  7. Install the LH rear wheel. See Wheel Assembly (Remove and Install).