2024-11-11

Rear Suspension Arms - Rear Lower Aft Link (Remove and Replace)

Correction code 3103030102 FRT 0.65 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1081765-00-A 3/4 TON UNDERHOIST STAND
  • 1459409-00-A ADAPTER, HUB JACK, MODEL 3

Torque Specifications

Table 1. Torque Specifications: Rear Suspension Arms - Rear Lower Aft Link (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the front of the diffuser to the body
4 Nm (2.9 lbs-ft)
  • Cordless 3/8in Dr Impact
  • 2 in extension
  • 10 mm socket
Reuse
Bolt and nut that attach the LH rear lower aft link to the rear subframe
115 Nm (84.8 lbs-ft)
  • 21 mm socket
  • 21 mm combination wrench
Reuse

Remove

  1. Inspect the vehicle for abnormal tire wear that might indicate the need for a wheel alignment. Note any findings.
  2. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  3. Remove the LH rear suspension cover. See Rear Suspension Cover - LH (Remove and Replace).
  4. Remove the mid aero shield panel. See Aero Shield - Middle (Remove and Replace).
  5. Remove the bolts (x2) that attach the front of the diffuser to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless 3/8in Dr Impact
    • 2 in extension
    • 10 mm socket
  6. Remove the LH rear suspension spring. See REAR SPRING - REAR WHEEL DRIVE (Remove and Replace).
  7. Remove the bolt and nut that attach the LH rear lower aft link to the rear subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
    • 21 mm combination wrench
  8. Remove the LH rear lower aft link from the subframe.

Install

  1. Install the LH rear lower aft link to the rear subframe, then install and hand-tighten the bolt and nut that attach the link to the subframe.
    Informational PurposesAn informational icon, calling your attention
    Note
    The step of tightening this bolt is included in the installation of the LH rear suspension spring.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21 mm socket
    • 21 mm combination wrench
  2. Install the LH rear suspension spring. See REAR SPRING - REAR WHEEL DRIVE (Remove and Replace).
  3. Install the bolts (x2) that attach the front of the diffuser to the body.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless 3/8in Dr Impact
    • 2 in extension
    • 10 mm socket
  4. Install the LH rear suspension cover. See Rear Suspension Cover - LH (Remove and Replace).
  5. Install the mid aero shield panel. See Aero Shield - Middle (Remove and Replace).
  6. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  7. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.