2025-03-12

CABIN CARPET - FRONT - LEFT HAND (Remove and Replace)

Correction code 1530030202 FRT 0.25 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Torque Specifications

Table 1. Torque Specifications: CABIN CARPET - FRONT - LEFT HAND (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x4) that attach the driver seat to body
33.5 Nm (24.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • Torx Plus TP45 Bit Socket
  • Ratchet/torque wrench
Replace

Remove

  1. Remove the lower A-pillar assembly. See A PILLAR LOWER TRIM - LEFT HAND (Remove and Install).
  2. Release the clips (x4) that attach the LH front seat harness to the sill trim.
  3. Pull the LH front seat harness out from under the LH front cabin carpet.
  4. Move the LH front seat fully forward.
  5. Open the LH rear door and lower the LH rear window.
  6. Remove and discard the bolts (x2) that attach the rear of the driver seat to body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx Plus TP45 Bit Socket
    • Ratchet/torque wrench
  7. Move the LH front seat fully rearward.
  8. Remove and discard the bolts (x2) that attach the front of the driver seat to body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx Plus TP45 Bit Socket
    • Ratchet/torque wrench
  9. Tilt the LH front seat rearward to gain access to the underside of the LH front seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to disconnect the LH seat harness from the body controller.
  10. Remove the LH center console front side panel. See CONSOLE SIDE PANEL LEFT HAND (Remove and Replace).
  11. Use a small flat head screwdriver to release the black tabs and then remove the OBD port.
  12. Release the clips (x2) that attach the LH front carpet to the body, and then remove the LH front carpet from the vehicle.

Install

  1. Install the LH front carpet into the vehicle and fasten the clips (x2) that attach the LH front carpet to the body.
  2. Install the OBD port.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the black tabs are properly installed.
  3. Install the LH center console front side panel. See CONSOLE SIDE PANEL LEFT HAND (Remove and Replace).
  4. Return the LH front seat to the vertical position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care when moving the seat. Ensure the carpet is not damaged.
  5. Install new bolts (x2) to attach the front of the driver seat to body.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx Plus TP45 Bit Socket
    • Ratchet/torque wrench
  6. Move the LH front seat fully forward.
  7. Install new bolts (x2) to attach the rear of the driver seat to body.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx Plus TP45 Bit Socket
    • Ratchet/torque wrench
  8. Raise the LH rear window and close the LH rear door.
  9. Move the LH front seat to original position.
  10. Route the 1st row LH seat harness under the LH front carpet, position the harness in the harness guide, and then install the clips (x4) that attach the harness to the sill trim.
    Informational PurposesAn informational icon, calling your attention
    Note
    Tuck the excess harness between the harness bracket and body.
  11. Install the LH lower A-pillar assembly. See A PILLAR LOWER TRIM - LEFT HAND (Remove and Install).
  12. Raise the LH front window and close the LH front door.