2025-09-11

Audio Speaker - Middle - Headliner - LH (Model YL) (Remove and Replace)

Correction code 15200200702 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Torque Specifications

Table 1. Torque Specifications: Audio Speaker - Middle - Headliner - LH (Model YL) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH rear coat hook to the headliner
2.5 Nm (1.8 lbs-ft)
  • Torx T25 socket
 Reuse
Bolt that attaches the headliner to the body
2 Nm (1.5 lbs-ft)
  • Torx T30 socket
 Reuse
Bolts (x2) that attach the LH middle headliner audio speaker to the headliner
0.65 Nm (6 lbs-in)
  • Torx T10 bit
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
 Reuse

Remove

  1. Remove the LH B-pillar lower trim. See Trim - B-Pillar - Lower - LH (Model YL) (Remove and Replace).
  2. Release the clip that attaches the LH B-pillar lower air duct to the body.
  3. Release the clips (x5) that attach the LH B-pillar upper trim assembly to the vehicle, and then move the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the bottom of the upper B-pillar inwards, and then pull the top to release the remaining clips.
  4. Push to open the LH rear coat hook.
  5. Release the tab to open the LH rear coat hook bolt cover.
  6. Remove the bolt that attaches the LH rear coat hook to the headliner.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  7. Release the tab to partially release the headliner from the body, and then remove the bolt that attaches the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  8. Carefully insert an inflatable airbag between the headliner and the body, and inflate the airbag.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the headliner.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to gain access to the airbag ramp.
  9. Disconnect the LH middle headliner audio speaker connector.
  10. Remove the bolts (x2) that attach the LH middle headliner audio speaker to the headliner, and then release the datums (x2) to remove the speaker from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm

Install

  1. Align the datums (x2) to install the speaker to the vehicle, and then install the bolts (x2) that attach the LH middle headliner audio speaker to the headliner.
    0.65 Nm (6 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  2. Connect the LH middle headliner audio speaker connector.
  3. Deflate the inflatable airbag, and then remove it from the vehicle.
  4. Install the bolt that attaches the headliner to the body, and then install the tab that attaches the headliner to the body.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 socket
  5. Install the bolt that attaches the LH rear coat hook to the headliner.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  6. Engage the tab to close the LH rear coat hook bolt cover.
  7. Push to close the LH rear coat hook.
  8. Align location pins (x2) to the slots on the body, and then secure the clips (x5) that attach the LH upper B-pillar trim assembly to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure that the air vent is properly installed.
  9. Install the clip that attaches the LH B-pillar lower air duct to the body.
  10. Install the LH B-pillar lower trim. See Trim - B-Pillar - Lower - LH (Model YL) (Remove and Replace).