2025-03-12

MOVING SIDE GLASS - FRONT DOOR - LEFT HAND (Remove and Replace)

Correction code 1020010102 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1454796-00-A TOOLKIT, WINDOW SWITCH
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The side impact airbag deployment depends on the front door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the front door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the front doors and their components.

Torque Specifications

Table 1. Torque Specifications:
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attaches the regulator guide block
12 Nm (8.8 lbs-ft)
  • 10 mm socket
Reuse

Remove

  1. Remove the LH front door trim panel. See Panel - Door Trim - Front - LH (LHD) (Remove and Replace).
  2. Remove the LH front door inner belt seal. See INNER BELT SEAL - FRONT DOOR - LEFT HAND (Remove and Replace).
  3. Remove the LH front door outer belt seal. See OUTER BELT - FRONT DOOR - LEFT HAND (Remove and Replace).
  4. Remove the plugs that cover the openings in door for access to the regulator guide blocks.
  5. Connect the window switch tool to the LH front door electrical harness.
  6. Latch the LH front door to allow the window to raise fully, and then raise the window for access to the regulator guide blocks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not close the door with the window in this position.
  7. Remove the bolt that secures the rearmost regulator guide block.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Loosen the bolt that secures the foremost regulator guide block, and then secure a set of suction cups to the door glass to remove the glass from the door.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket

Install

  1. Inspect the regulator guide blocks for glass splinters or other debris, and clean them if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  2. Position the LH front door glass onto the LH front door, and then hand-tighten the bolts (x2) that secure the glass to the guide blocks.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the clamps are not bottomed out on the regulator.
  3. Release the LH front door latch by pulling the emergency release cable.
  4. Lower the LH front window fully.
  5. Install the LH front door outer belt seal. See OUTER BELT - FRONT DOOR - LEFT HAND (Remove and Replace).
  6. Install the LH front door inner belt seal. See INNER BELT SEAL - FRONT DOOR - LEFT HAND (Remove and Replace).
  7. Request an assistant sit in the driver seat, and then close the LH front door.
  8. Raise the LH front window fully using the window switch tool.
  9. Inspect the LH front window for proper gap and flushness.
  10. Have the assistant tighten the bolts (x2) that secure the glass to the isolator clamps.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Having the assistant perform this step can avoid position change of the window.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  11. Lower the LH front window fully and open the LH front door.
  12. Disconnect the window switch tool.
  13. Install the plugs that cover the openings in door.
  14. Install the LH front door trim panel. See Panel - Door Trim - Front - LH (LHD) (Remove and Replace).