2025-03-27

Assembly - Fascia and Diffuser - Rear (Remove and Install)

Correction code 10010501601 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Assembly - Fascia and Diffuser - Rear (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the corner of the rear fascia to the body
3.5 Nm (2.6 lbs-ft)
  • 10 mm socket
 Reuse
Bolt that attaches the rear fascia to the body
2 Nm (1.5 lbs-ft)
  • 8 mm socket
 Reuse
Rear diffuser bolts
5 Nm (3.7 lbs-ft)
  • 10 mm deep socket
 Reuse

Remove

  1. Place the vehicle on the 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Ensure the vehicle is not charging.
  2. Remove both rear fender garnishes. See Garnish - Fender - Rear - LH (Remove and Replace).
  3. Open the liftgate.
  4. Apply masking tape around the LH corner of the rear upper fascia.
  5. Release 3 clips of the LH rear trough trim.
  6. Remove the bolt that attaches the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Remove the bolt that attaches the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  8. Repeat step 4 to 7 to the RH side.
  9. Raise the vehicle to a comfortable working height, and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  10. Remove the bolts (x2) that attach the mid aero shield to the rear diffuser.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  11. Remove the bolts (x7), push clips (x6) and fastener covers (x2) from the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  12. Lower the vehicle to a comfortable working height and set the lift onto locks.
  13. With assistance, release the rear fascia assembly from the body, disconnect the electrical connector, and place the assembly on a padded surface to avoid damage.

Install

  1. With assistance, connect the electrical connector, and secure the rear fascia assembly onto the body.
  2. Install the bolt that attaches the LH corner of the rear fascia to the body.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Secure the clips (x3) to the LH rear trough trim.
  4. Install the bolt that attaches the LH rear fascia to the body.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  5. Install the LH rear fender garnish. See Garnish - Fender - Rear - LH (Remove and Replace).
  6. Repeat step 2 to 5 to the RH side.
  7. Remove the masking tape from the LH and RH corners of the rear upper fascia.
  8. Raise the vehicle to a comfortable working height, and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  9. Install the bolts (x2) that attach the mid aero shield to the rear diffuser.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  10. Install the bolts (x7), push clips (x6) and fastener covers (x2) to the rear fascia diffuser.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  11. Fully lower the vehicle.
  12. Close the liftgate.
  13. Remove the vehicle from the lift.