2025-01-19

Tube- Rear Drive Inverter to Oil Cooler - 3DU (Remove and Replace)

Correction code NEW FRT 0.85 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1080568-00-A Fluid Catcher
  • 1135762-00-A Kit, Svc Plug, Cooling Hose, Model 3
  • 1065131-00-A Battery Coolant Drain Kit

Remove

  1. Raise and support vehicle.
  2. Open LH front door, and Lower LH front window.
  3. Unlock the gateway. See Gateway (Unlock).
  4. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Thermal > Coolant System > Start Thermal Fill/Drain > Run, and allow the routine to complete.
  5. Disconnect the LV battery. See LV Power (Disconnect and Connect).
  6. Remove the rear diffuser from rear lower fascia. See Rear Fascia - Diffuser (Remove and Replace).
  7. Remove nut securing RDU ground strap to vehicle.
  8. Position coolant drain container under LH rear of vehicle.
  9. Release RDU inverter to oil cooler hose and plug both ends.
  10. Position coolant drain underneath RH rear of drive unit.
  11. Release RDU inverter coolant hose from heat exchanger and plug both ends.
  12. Release clips securing RDU inverter to oil cooler hose.
  13. Remove RDU inverter to oil cooler hose.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently wiggle hose out from RDU.

Install

  1. Install RDU inverter to oil cooler hose.
    Informational PurposesAn informational icon, calling your attention
    Note
    Routine inverter to oil cooler hose to RDU.
  2. Secure RDU inverter to coolant hose onto RDU.
  3. Remove plugs and secure RDU inverter to oil cooler hose onto heat exchanger.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean excess coolant from area, Perform push-pull-push test to make sure hose is fully engaged.
  4. Remove plugs and secure inverter to cooler hose to inverter.
    Informational PurposesAn informational icon, calling your attention
    Note
    Perform push-pull-push test to make sure hose is fully engaged.
  5. Remove coolant drain container from underneath vehicle.
  6. Install nut securing RDU ground strap to vehicle.
  7. Install the rear diffuser to rear lower fascia. See Rear Fascia - Diffuser (Remove and Replace).
  8. Install the mid aero shield. See Aero Shield - Middle (Remove and Replace).
  9. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  10. Lower vehicle fully.
  11. Remove coolant bottle cap.
  12. Connect the LV battery. See LV Power (Disconnect and Connect).
  13. Unlock the gateway. See Gateway (Unlock).
  14. Select Stop Thermal Fill/Drain > Run, and allow the routine to complete.
  15. Select Coolant Purge Start > Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure vehicle is not in Drive, shifting the vehicle into Drive will stop this routine. The test will last approximately 10 mins. The test will vary speeds from 3500-6500 RPM (idle speed = ~1500 RPM) and actuate the valve between series and parallel. If speed hovers at 7000 RPM, it indicates the pump is air locked, perform the vacuum fill again. Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle.
  16. Install the HEPA filter assembly. See SERVICE KIT - HEPA AND CARBON FILTERS (Remove and Replace).
  17. Remove the vehicle from the 2 post lift. See Raise Vehicle - 2 Stands.