2026-02-10

Podium - 2nd Row Seat - LH (7-Seat) (Remove and Replace)

Correction code 1302010501 1302010502 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Remove

  1. Remove the 2nd LH seat assembly. See Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace).
  2. Remove the 2nd row LH toe kick panel. See Cover - Toe Kick - 2nd Row - LH (7-Seat) (Remove and Replace).
  3. Remove the 2nd row LH seat side shield. See Outer Sideshield - Outboard - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  4. Remove the center back panel from the 2nd row center seatback.
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift up at the lower back panel and then slide forward to release it.
  5. Remove the 2nd row LH seat inboard outer B-cover. See Trim - B-Cover Inboard Outer - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  6. Remove the 2nd row LH seat inboard inner B-cover. See B-Cover Inboard Inner - 2nd Row - LH (7-Seate) (Remove and Replace).
  7. Remove the seat pan fastener from the LH front of the 2nd row LH seat.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm 12-point deep socket
  8. Remove the push clips (x2) from the front of the 2nd row LH bottom seat pan.
  9. Lift the front of the 2nd row LH seat cushion to allow access to the podium fasteners.
  10. Remove the harness clip from the podium, and then remove and discard the bolts (x2) that secure the 2nd row LH podium.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 11 mm socket

Install

  1. Install new bolts (x2) (1616775-00-B) that secure the 2nd row LH podium, and then install the harness clip.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 11 mm socket
  2. Push the front of the seat cushion back into place and install the clips (x2).
  3. Install the seat pan fastener to the LH front of the 2nd row LH seat.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm 12-point deep socket
  4. Install the 2nd row LH seat side shield. See Outer Sideshield - Outboard - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  5. Install the 2nd row LH seat inboard inner B-cover. See B-Cover Inboard Inner - 2nd Row - LH (7-Seate) (Remove and Replace).
  6. Install the 2nd row LH seat inboard outer B-cover. See Trim - B-Cover Inboard Outer - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  7. Insert the back panel hooks (x2) into the center seat back assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Engage the hooks and slide the panel rearward into position. Early production have 4 hooks.
  8. Install the center back panel onto the seat back (5x clips).
  9. Install the 2nd row LH toe kick panel. See Cover - Toe Kick - 2nd Row - LH (7-Seat) (Remove and Replace).
  10. Install the 2nd LH seat assembly. See Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace).
  11. Place the vehicle in Service Mode by using the touchscreen. See Service Mode.
  12. Unlock the vehicle gateway. See Gateway (Unlock).
  13. Perform the following routine using Service Mode or Toolbox (see 0005 - Service Modes): PROC_VCLEFT_X_2R-SEAT-RECLINE-CALIBRATIONvia Service Mode:Low Voltage ➜ Second Row Seats ➜ Calibratevia Toolbox:(link)
  14. Exit Service Mode or disconnect the laptop if applicable (see 0005 - Service Modes).