2024-11-11

Airbag - Driver (Remove and Replace)

Correction code 2001010202 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Make sure LV power has been disconnected for at least 2 minutes before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see .
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Supplementary Restraint System (SRS) components can be hazardous if not handled properly. For more information on SRS precautions, see .

Remove

  1. Disconnect the LV battery power. See LV Power (Disconnect and Connect).
  2. Press the spring clips (x2) from the 2 access holes to release the driver airbag from the steering wheel, and then partially pull the airbag away from the steering wheel.
    Informational PurposesAn informational icon, calling your attention
    Note
    The holes are located at 4 and 8 o’clock position.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not insert the tool too far as the airbag electrical connector could be damaged.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the driver airbag from the steering wheel yet because the airbag electrical connector is still connected to the steering wheel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Note how the airbag is attached to the steering wheel to aid in installation. Failure to fully seat both sides of the airbag can result in the airbag falling out or not performing as intended.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Pin punch or any other straight tool that is 3 mm wide and at least 30 mm long.
  3. Disconnect the driver airbag electrical connector, and then remove the airbag from the vehicle.

Install

  1. Connect the driver airbag electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure the harness does not get caught between the airbag and the horn.
  2. Position the driver airbag assembly onto the steering wheel so that the datums are aligned with the clips.
  3. Press the LH side of the driver airbag assembly into the steering wheel until an audible click is heard and the spring clip is fully seated.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Failure to fully seat both sides of the airbag can result in the airbag falling out or not performing as intended.
  4. Press the RH side of the driver airbag assembly into the steering wheel until an audible click is heard and the spring clip is fully seated.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Failure to fully seat both sides of the airbag can result in the airbag falling out or not performing as intended.
  5. Perform a light pull test on the LH side of the driver airbag to verify that it is properly secured to the steering wheel.
  6. Perform a light pull test on the RH side of the driver airbag to verify that it is properly secured to the steering wheel.
  7. Check that the gap between the driver airbag assembly and the steering wheel is consistent around the perimeter of the airbag.
  8. Connect the LV battery power. See LV Power (Disconnect and Connect).