2025-02-05

Glass - Door - LH - Rear (Adjust)

Correction code 11010004 Adjustable FRT NOTE: This procedure uses an adjustable correction code. Use the correction code listed above and manually enter the actual amount of time spent performing this procedure. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1135305-00-A Tool, Window Switch Bypass, Model 3
  • 1129348-00-A XP-10 Power Supply, XP-10
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The side impact airbag deployment depends on the rear door sensor's ability to detect a side impact from air pressure. Make sure that there are no uncovered holes in the rear door shells. Additionally, always reinstall plugs or tape when servicing or inspecting the rear doors and their components.

Procedure

  1. Remove the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).
  2. Remove the plugs (x2) that cover the openings in the door to gain access to the bolts that attach the window glass.
  3. Connect the window switch special tool and adjust the window to access the regulator guide blocks.
  4. Loosen the fasteners (x2) that attach the window glass to the window regulator clamps about 1/2 turn to maintain the position of the window but still allow adjustment.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Release LH front door latch by pulling the emergency release cable.
  6. Close the LH rear door.
  7. Raise the LH rear window using the driver's master switch.
  8. Check the gap and flush on the LH rear window and adjust it, if necessary.
    1. Open the LH rear door.
    2. Latch the LH rear door to allow window height adjustment.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      CAUTION
      Do not close the door with the window fully raised, as upper bright trim will be damaged.
    3. Using the window switch tool, adjust the glass for access to the regulator guide blocks.
    4. Adjust the front of the moving glass to achieve flush target to the B-pillar applique.
      Informational PurposesAn informational icon, calling your attention
      Note
      Use a 5mm hex socket (newer vehicles might use Torx T25) to adjust the friction pad to tilt the glass inboard or outboard.
    5. Adjust the rear of the moving glass to achieve flush target to quarter glass assembly.
      Informational PurposesAn informational icon, calling your attention
      Note
      Use a 5mm hex socket (newer vehicles might use Torx T25) to adjust the friction pad to tilt the glass inboard or outboard.
    6. Adjust the moving glass to achieve the gap target, and then hand tighten the regulator fasteners (x2).
  9. Release LH front door latch by pulling the emergency release cable.
  10. Close the LH rear door.
  11. Check the LH rear window for gap and flush and re-adjust, if necessary.
  12. Open the LH rear door.
  13. Latch the LH rear door to allow window height adjustment, and then adjust the window for access to the regulator guide blocks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not close the door with the window raised fully, as upper bright trim will be damaged.
  14. Inspect the regulator guide blocks for glass splinters or other debris, and clean them if necessary.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Debris and splinters may damage or shatter the new door glass.
  15. Tighten the fasteners that attach the window glass to the window regulator.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  16. Release the LH rear door latch by pulling the emergency release cable.
  17. Lower the LH rear window.
  18. Install the plugs (x2) that cover the openings in the door for access to the fasteners securing the glass.
  19. Disconnect the window switch special tool and reconnect the window switch electrical connector.
  20. Install the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Install).