2025-03-12

REAR DOOR - LEFT HAND (Remove and Install)

Correction code 1010020501 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: REAR DOOR - LEFT HAND (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH rear door check strap to the body
24 Nm (17.7 lbs-ft)
  • Torx T40 socket
  • 4 in extension
  • Ratchet/torque wrench
Reuse
Bolts (x2) that attach the LH rear door assembly to the hinges
49 Nm (36.1 lbs-ft)
  • Ratchet/torque wrench
  • 13 mm deep socket
Reuse

Remove

  1. Open the LH doors and lower the LH windows.
  2. Place the vehicle in Service Mode by using the touchscreen. See Service Mode.
  3. Disconnect the LV battery power. See LV Power (Disconnect and Connect).
  4. Release the grommet between the 2 hinges, and then release the clips (x2) that attach the electrical harness connector to the door to disconnect the harness from the B-pillar area.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the top clip at first, and then while pressing the top one, release the bottom clip.
  5. Use tape to mark the position of the LH rear door hinges and the LH rear door check strap.
    Figure 1. Check Strap Area as Example
  6. Remove the bolt that attaches the LH rear door check strap to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Unbolting the door check allows the door to swing freely beyond opening limits.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
    • 4 in extension
    • Ratchet/torque wrench
  7. With assistance, loosen the bolts (x2) that attach the LH rear door assembly to the hinges, and then fully remove the bottom bolt, then fully remove the top bolt.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13 mm deep socket
  8. With assistance, remove the LH rear door assembly from the vehicle, and place it on a padded surface.

Install

  1. With assistance, position the LH rear door assembly to the vehicle.
  2. With assistance, hand-tighten the bolts (x2) that attach the LH rear door assembly to the hinges.
  3. Install the bolt that attaches the LH rear door check strap to the body.
    24 Nm (17.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
    • 4 in extension
    • Ratchet/torque wrench
  4. Verify the seal is fully seated around the white clips.
  5. Secure the clips (x2) that attach the electrical harness connector to the door until there is an audible click, and then seat the grommet into position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently pull the harness to ensure the connector is fully secure.
  6. Connect the LV battery power. See LV Power (Disconnect and Connect).
  7. Close the LH rear door to check for gap/flushness.
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust the LH rear door if necessary. Refer to CVIS for current specification.
  8. Open the LH rear door.
  9. With assistance, torque the bolts (x2) that attach the LH rear door assembly to the hinges.
    49 Nm (36.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 13 mm deep socket
  10. Remove all masking tapes.
  11. Raise the LH rear window and lower the LH rear door.
  12. Unlock the vehicle gateway. See Gateway (Unlock).
  13. On the touchscreen, tap the Service Mode "wrench" (at the bottom of the touchscreen UI), and then tap Closures > Windows > Rear Left Calibrate, click Run, and allow the routine to complete.
  14. Exit Service Mode. See Service Mode.
  15. Raise the LH front window and close the LH front door.