2025-03-12

DRIVEN HUB 142MM FLANGE (Remove and Replace)

Correction code 3101010102 FRT 0.35 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1096075-00-A Tool, Hub Puller, Hydraulic
  • 1062500-00-A Card, Magnetic Field Viewer

Torque Specifications

Table 1. Torque Specifications: DRIVEN HUB 142MM FLANGE (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x3) that attach the LH front hub to the LH front knuckle
115 Nm (84.8 lbs-ft)
  • 18 mm socket
Reuse
Bolt that attaches the LH front brake rotor to the knuckle
5 Nm (3.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • 10 mm deep socket
  • Ratchet/torque wrench
Reuse
Bolts (x2) that attach the LH front caliper to the LH front knuckle
94 Nm (69.3 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • External Torx E18
  • Ratchet/torque wrench
Replace 1088969-00-B
Bolt that attaches the LH front brake hose bracket to the LH front knuckle
5 Nm (3.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 4 in extension
  • 10 mm socket
  • Ratchet/torque wrench
Reuse
The LH front halfshaft nut
300 Nm (221.2 lbs-ft)
  • 32 mm deep impact socket
Replace 1765133-00-A

Remove

  1. Raise and support the vehicle. See Raise Vehicle - 2 Stands.
  2. Remove the LH front wheel cap.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use wheel trim removal tool to release the clips.
  3. Loosen the LH front drive unit halfshaft nut.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Long Breaker Bar
    • 32 mm deep impact socket
  4. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  5. Remove the bolt that attaches the LH front brake hose bracket to the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  6. Remove and discard the bolts (x2) that attach the LH front brake caliper to the LH front knuckle, remove the caliper from the knuckle, and allow the caliper to hang from an S-hook.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • Ratchet/torque wrench
  7. Remove and discard the LH front drive unit halfshaft nut and washers.
    Informational PurposesAn informational icon, calling your attention
    Note
    The washers are attached to the nut.
  8. Remove the bolt that attaches the LH front brake rotor to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • 10 mm deep socket
    • Ratchet/torque wrench
  9. Position the hydraulic hub puller tool onto the LH front wheel studs, and then hand tighten the wheel lug nuts (x5).
  10. Separate the LH front drive unit halfshaft from the LH front hub assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    While holding the hub in position, turn the hydraulic hub puller tool handle clockwise to separate the LH front drive unit halfshaft from the hub assembly.
  11. Remove the hub puller tool from the LH front wheel studs.
  12. Remove the LH front rotor from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Store the rotor face down to reduce likelihood of damage to the rotor face.
  13. Remove the bolts (x3) that attach the LH front hub to the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18 mm socket
  14. Remove the LH front hub from the vehicle.

Install

  1. Check the tone ring on the LH front hub prior to installation: Use a magnetic field viewing card to make sure that the magnetic field on the tone ring is not damaged.
  2. Apply Molykote M-77 Lubricant Paste to the outboard side of the LH rear halfshaft assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Clean the halfshaft before applying if necessary.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply no more than 1 gram to axle only.
  3. Line up the LH front drive unit halfshaft splines, and then install the LH front hub on the LH front knuckle.
  4. Install the bolts (x3) that attach the LH front hub to the LH front knuckle.
    115 Nm (84.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18 mm socket
  5. Install the LH front brake rotor onto the vehicle.
  6. Install the bolt that attaches the LH front brake rotor to the knuckle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • 10 mm deep socket
    • Ratchet/torque wrench
  7. Install and hand tighten a new halfshaft nut and washer on the halfshaft.
  8. Install new bolts (x2) that attach the LH front caliper to the LH front knuckle.
    94 Nm (69.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark with a pen after installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • Ratchet/torque wrench
  9. Install the bolt that attaches the LH front brake hose bracket to the LH front knuckle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  10. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  11. Fully tighten the new LH front drive unit halfshaft nut.
    300 Nm (221.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32 mm deep impact socket
  12. Install the LH front wheel cap.
    Informational PurposesAn informational icon, calling your attention
    Note
    Align valve stem with the wheel cap cavity.
  13. Remove the vehicle from the lift. See Raise Vehicle - 2 Stands.