2026-07-29

Clean Radiator (Pressure Washer Kit) (Maintenance)

Correction code 18302000 FRT 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-07-29: Released new procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
This procedure requires the availability of Pressure Washer Kit (2325255-00-A). If it is unavailable, clean the radiator with a blow gun. Refer to Clean Radiator (Maintenance).
Equipment:
  • 2325255-00-A - Pressure Washer Kit
  • 2303607-00-A - Waterproof plug of connector

Torque Specifications

Table 1. Torque Specifications: Clean Radiator (Pressure Washer Kit) (Maintenance)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x3) that secure the washer tank to the front end carrier
4 Nm (2.9 lbs-ft)
  • 10 mm socket
 Reuse
LH and RH bolts (x2) that attach the cooling fan module assembly to the front end carrier
6 Nm (4.4 lbs-ft)
  • 8 mm socket
Reuse

Procedure

  1. Place the vehicle on the 2-post lift.
  2. Open the LH front door and lower the LH front window.
  3. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  4. Disconnect the LV power. See LV Power (Disconnect and Connect) (Modify).
  5. Disconnect the front fascia camera washer hose, and then release the clip that attaches the hose to the vehicle.
  6. Remove the bolts (x3) that attach the washer reservoir to the front end carrier, and then move the reservoir aside.
    Informational PurposesAn informational icon, calling your attention
    Note
    Be careful not to spill washer fluid from the reservoir.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. Release the connector lock, and then disconnect the active grille shutter actuator electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not push down on the red tab. Pull the red tab to release the connector lock.
  8. Install the waterproof connector plugs (2303607-00-A) to the active grille shutter electrical connector, hood latch connector and LV battery connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Keep the harness and connectors away from the radiation to avoid water ingress.
  9. Release the tabs (x2) and attach the ambient temperature sensor to the active grille shutter.
  10. Carefully remove the ambient temperature sensor cover from the active grille shutter, and then move the sensor out through the opening.
  11. Release the clips (x8) that attach the upper and middle of the active grille shutter to the cooling fan module.
  12. Remove the front valance. See Valance - Front Fascia (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the pedestrian warning speaker from the valance.
  13. Place towels to the front of subframe to protect the cooling fan in later steps.
  14. Remove the bolts (x2) that attach the LH and RH of the cooling fan module to the ankle catcher.
    Informational PurposesAn informational icon, calling your attention
    Note
    Be careful not to lose the bolt washer.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
    Figure 1. LH shown, RH similar
  15. Release the clips (x) that attach the lower of the active grille shutter to the cooling fan module.
  16. Fully lower the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise the lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
  17. Remove the active grille shutter from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care not to damage the radiator while removing the active grille shutter.
  18. Remove the locking tabs (x8) that attach the stone guard to the radiator.
  19. Place a fluid catcher underneath the front of the vehicle.
  20. Use a vacuum to clean the dirt on the radiator.
    Informational PurposesAn informational icon, calling your attention
    Note
    If necessary, remove any large debris.
  21. Use the pressure washer kit (2325255-00-A) to clean the dirt on the radiator again.
    1. Add clear water to the pressure washer kit.
    2. Connect the pressure washer kit to the shop compressed air.
    3. Flush the upper face of radiator until all the visible dirt is cleaned.
      Informational PurposesAn informational icon, calling your attention
      Note
      Do not get too close to the radiator blades.
      Informational PurposesAn informational icon, calling your attention
      Note
      Sweep the nozzle up and down, and make sure that the washer nozzle is perpendicular to the radiator surface during the whole flushing process.
      Informational PurposesAn informational icon, calling your attention
      Note
      Dust and debris may fly out during the process; make sure to protect the vehicle and wear proper PPE , such as a mask, safety glasses, etc.
  22. Release the upper and lower locking tabs (x2) that secure the radiator to the cooling and shroud assembly.
  23. Use an inflatable airbag to separate the radiator.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use an inflatable airbag to raise the edge of the radiator at a specific angle for better cleaning. Be careful not to damage the surface of the radiator and the two holding mounts.
  24. Clean the bottom of the cooling fan.
    Informational PurposesAn informational icon, calling your attention
    Note
    Avoid moving debris onto the fan.
  25. Inspect the bottom of the cooling fan for debris.
  26. Remove the fluid catcher from underneath the front of the vehicle.
  27. Remove the inflatable airbag.
  28. Install the upper and lower locking tabs (x2) that secure the radiator to the cooling and shroud assembly.
  29. Install the locking tabs (x8) that attach the stone guard to the radiator.
  30. Install the active grille shutter to the vehicle, and then install the clips (x8) that attach the upper and middle of the active grille shutter to the cooling fan module.
  31. Raise the vehicle to a comfortable working height, and lower the lift onto locks.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.
  32. Install the clips (x6) that attach the lower of the active grille shutter to the cooling fan module.
  33. Loosely install the bolts (x2) that attach the LH and RH of the cooling fan module to the ankle catcher.
    Figure 2. LH shown, RH similar
  34. Torque the bolts (x2) that attach the LH and RH of the cooling fan module to the ankle catcher.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
    Figure 3. LH shown, RH similar
  35. Remove the towels from the front of subframe.
  36. Install the front valance. See Valance - Front Fascia (Remove and Replace).
  37. Remove the waterproof connector plugs (2303607-00-A) from the connectors (x3).
    Informational PurposesAn informational icon, calling your attention
    Note
    Before removing the plugs, make sure there are no water droplets on the exterior of the plugs and the connectors, to prevent water from entering the interior of the connector during plug removal.
  38. Connect the active grille shutter actuator electrical connector, then engage the connector lock.
  39. Feed the ambient temperature sensor through the opening of the active grille shutter, and then install the tabs (x2) that attach the sensor to the active grille shutter.
  40. Move the washer reservoir back to its original position, and then install the bolts (x3) that attach the washer reservoir to the front end carrier.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  41. Fasten the clip that attaches the front camera hose to the washer reservoir, and then connect the front camera washer hose..
  42. Connect the LV power. See LV Power (Disconnect and Connect) (Modify).
  43. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  44. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox (Connect and Disconnect).
  45. In toolbox, click Actions tab, type Radiator in the search field, select PROC_VC_X_RESET-RADIATOR-UA-INDEXvia Toolbox:(link), click Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Note
    Only if the vehicle software is 2026.14.3 or later, this routine can be performed in the touchscreen.
  46. Disconnect the laptop.
  47. Perform the following routine using Service Mode or Toolbox (see 0005 - Service Modes): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Service Mode:Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    via Toolbox:(link)
  48. Disable Service Mode. See Service Mode.
  49. Raise the LH front window and close the LH front door.
  50. Remove the vehicle from the lift.