Correction code TBD FRT 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

1. Open all four doors

   

2. Lower all four windows

   

3. Move LH front seat forward
   Note

   Adjust seat back if needed to avoid contacting headliner

   

4. Move RH front seat forward
   Note

   Adjust seatback if needed to avoid contacting headliner

   

5. Move 60 seat to easy entry position
   Note

   Press shoulder switch then push seat forward

   

   

6. Partially remove lower portion of LH rear door seal

   

7. Remove LH 7s lower C-pillar trim
   Note

   8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips

   

   

8. Move 60 seat to original position
   Note

   Press shoulder switch then pull seat backward

   

9. Fold 2nd row 60 seatback down
   Note

   Via seat switch or manual tether, Protect seat back upholstery if necessary

   

   

10. Disconnect 2nd row 60 seat connector
    Note

    1x connector,

    

    

11. Move 60 seat forward using towel bar
    Note

    With one hand on towel bar pull up and slide the seat forward with your other hand

    

    

12. Remove 60 seat rear outboard track fastener
    Note

    1x patch bolt, 11mm, 37 Nm, Discard after removal

    

13. Remove 60 seat rear inboard track fasteners
    Note

    2x patch bolts, 11mm, 37 Nm, Discard after removal

    

14. Move 60 seat fully rearward using towel bar
    Note

    pull up bar, slide seat forward

    

15. Remove 60 seat outboard track cover
    Note

    1x clip, Slide covers forward to release from 60 seat tracks

    

    

    

16. Remove center track cover from 2nd row seats
    Note

    2x clips, Slide covers forward to release from 2nd row seat tracks

    

    

    

17. Release cabin carpet from 60 seat
    Note

    Pull cabin carpet towards front of vehicle

    

    

18. Remove 60 seat front inboard track fasteners
    Note

    1x bolts, 11mm, 37 Nm, Discard after removal

    

19. Remove 2nd row 60 seat frame front outboard track fasteners
    Note

    1x bolts, 11mm, 37 Nm, Discard after removal

    

20. Remove 2nd row 60 seat assembly from vehicle
    Note

    Recommend assistance, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement

    

    

21. Move RH front seat forward
    Note

    Adjust seatback if needed to avoid contacting headliner

    

22. Move 60 seat to easy entry position
    Note

    Press shoulder switch then push seat forward

    

    

23. Partially remove RH rear door seal
    Note

    Pillar and sill trim have tabs seated underneath seal

    

24. Remove RH C-pillar lower trim
    Note

    5x clips, Rear edge is mated with groove in trunk side trim, Release clips at front of LH Lower C-Pillar trim working your way back towards rear of sill trim, trim part may slightly differ by vehicle build location, and the number of clips may also varyt, by vehicle build location, Confirm each installation with push-pull test, Clip position should not be adjusted after bracket is removed or will result in bracket not seating properly, if clip position is changed or push-pull action shows bracket not secure, remove clip from tab and seat clip into doghouse on bracket and reinstall

    

    

25. Move 40 seat to original position
    Note

    Press shoulder switch then pull seat backward

    

26. Fold 2nd row 40 seatback down
    Note

    Via seat switch or manual tether, Protect seat back upholstery if necessary

    

    

27. Remove 40 seat outboard track cover
    Note

    1x clip, Slide cover forward to release from 40 seat track

    

28. Remove bolts securing 40 seat podium to vehicle
    Note

    2x patch bolts, 11mm, 37 Nm, Discard bolts after removal

    

29. Move 40 seat forward using towel bar
    Note

    With one hand on towel bar pull up and slide the seat forward with your other hand

    

30. Remove bolts securing 40 seat inner and outer tracks to vehicle
    Note

    2x patch bolts, 11mm, 37 Nm, Discard bolts after removal

    

31. Move 40 seat fully rearward using towel bar
    Note

    pull bar, slide seat forward

    

32. Disconnect 2nd row 40 seat connector
    Note

    1x connector, Newer models may have red locking tab

    

    

33. Remove 40 seat from vehicle
    Note

    Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement

    

    

34. Remove 3rd row seat cushion
    Note

    2x clips, 1x connector, 2x circular hooks, Press tabs backward then pull front edge up, Press rear seat cushion and lift the front seat cushion

    

    

    

    

    

35. Remove 3rd row LH seat cushion bolster
    Note

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster towards front of vehicle to remove

    

36. Remove 3rd row RH seat cushion bolster
    Note

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster towards front of vehicle to remove

    

    

    

37. Release LH side of 3rd row rear carpet
    Note

    2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Remove bolt then release carpet

    

    

    

    

38. Release RH side of 3rd row rear carpet
    Note

    2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Remove bolt then release carpet

    

    

    

    

39. Remove 3rd row rear cabin carpet

    

    

40. Open hood

    

    

41. Power off vehicle from center display
    Note

    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box

    

    

42. Remove rear apron
    Note

    16x trim clips, 3x datums, 2x clips

    

    

    

    

43. Remove HEPA filter assembly
    Note

    2x bolts, 10mm, 10 Nm, Pivot rear edge up past brake reservoir then lift up to clear frunk assembly

    

    

    

    

44. Disconnect LV battery and first responder loop
    Note

    2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

    

    

    

45. Verify operation of multimeter
    Note

    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing the 16v battery

    

46. Remove 3rd row NVH insulator
    Note

    1x connector, Disconnect connector then remove insulator

    

    

    

    

47. Install HVC logic cap
    Note

    1x logic cap

    

48. Remove all items from pockets and ensure not wearing metal items

    

49. Inspect HV insulating gloves
    Note

    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves. https://service.teslamotors.com/documents?model=&keys=TN-15-92-003&vehicle_system=&sort_by=field_date_submitted&sort_order=DESC

    

50. Put on HV insulating gloves and leather over gloves
    Note

    Use HV cut resistant insulated gloves or HV insulating gloves and leather over gloves, HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used, Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration.

    

51. Remove bolts securing ancillary bay probe lid cover
    Note

    2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal

    

52. Remove ancillary bay probe lid cover

    

    

53. Verify no high voltage
    Note

    Make sure to wear PPE (HV gloves, Safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

54. Wipe ancillary bay cover with IPA to clean surface
    Note

    Allow to 1 minute dry time

    

55. Inspect ancillary bay probe lid cover gasket then position onto ancillary bay cover
    Note

    Confirm no visual damage present, Wipe ancillary bay with IPA to clean surface, Allow to 1 minute dry time

    

    

56. Install bolts securing ancillary bay probe lid cover to ancillary bay cover
    Note

    2x bolts, EP10 5-Lobe, 6 Nm, Install new bolts

    

57. Remove leather over gloves and HV insulating gloves

    

58. Remove HVC logic cap
    Note

    1x logic cap

    

59. Install 3rd row NVH insulator
    Note

    1x connector, Install insulator then connect connector

    

    

    

    

60. Position 3rd row rear cabin carpet

    

    

61. Secure RH side of 3rd row rear carpet
    Note

    2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Secure carpet then install bolt

    

    

    

    

62. Secure LH side of 3rd row rear carpet
    Note

    2x clips, 2x location pins, 1x bolt, H11, Lift trim to access bolt, Secure carpet then install bolt

    

    

    

    

63. Install 3rd row LH seat cushion bolster
    Note

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster into seat frame complete

    

    

64. Install 3rd row RH seat cushion bolster
    Note

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster into seat frame complete

    

    

    

65. Install 3rd row seat cushion and connect harness
    Note

    1x connector, Secure 3rd row seat cushion into RH and LH latches

    

    

66. Connect first responder loop and LV battery
    Note

    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

    

    

67. Install HEPA filter assembly
    Note

    2x bolts, 10mm, 10 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct, Do not pinch washer hose inbetween HEPA filter assembly and body

    

    

    

    

    

    

68. Install rear apron
    Note

    16x trim clips, 3x locator pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron

    

    

    

69. Close hood

    

    

70. Install 40 seat into vehicle
    Note

    Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium

    

    

71. Connect 2nd row 40 seat connector
    Note

    1x connector,

    

    

72. Install bolts securing 40 seat podium to vehicle hand tight
    Note

    2x patch bolts, 11mm, 37 Nm, Install new bolts, Torque at later step

    

73. Move 40 seat forward using towel bar
    Note

    pull up bar, slide seat forward

    

74. Install bolts securing 40 seat inner and outer tracks to vehicle
    Note

    2x patch bolts, 11mm, 37 Nm, Install new bolts

    

75. Move 40 seat to original position
    Note

    Press shoulder switch then pull seat backward

    

76. Install cabin carpet to 40 seat

    

77. Torque bolts securing 40 seat podium to vehicle
    Note

    2x patch bolts, 11mm, 37 Nm

    

78. Install center track cover to 2nd row seats
    Note

    2x clip, Slide cover straight on to clip to 2nd row seat tracks

    

    

    

79. Install 40 seat outboard track cover
    Note

    1x clip

    

80. Position 40 seat into easy entry mode
    Note

    Press shoulder switch and push 40 seat forward

    

    

81. Install RH rear sill trim
    Note

    4x tabs, 3x clips, 5x location pins, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips

    

    

82. Reseat RH rear door seal
    Note

    Seat pillar and sill trim tabs underneath seal

    

83. Move 40 seat to original position
    Note

    Press shoulder switch then pull seat backward

    

84. Move RH front seat to original position

    

85. Install 2nd row 60 seat assembly
    Note

    Recommend assistance

    

    

    

86. Connect 2nd row 60 seat connector
    Note

    1x connector,

    

    

87. Install fasteners securing 60 seat frame to body
    Note

    5x patch bolts, 11mm, 37 Nm, Install new patch bolts, bottom seat bolts located in rear

    

    

    

    

88. Secure cabin carpet to 60 seat
    Note

    Strap velcro on

    

    

89. Return 2nd row 60 seatback to vertical position
    Note

    Via trunk seat switch, Remove seatback protection if necessary

    

    

90. Install 60 seat outboard track cover
    Note

    1x clip

    

    

    

91. Position 60 seat into easy entry mode
    Note

    Press shoulder switch and push 60 seat forward to position into easy entry mode

    

    

92. Install LH 7s lower C-pillar trim
    Note

    8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips

    

    

93. Reseat LH rear door seal
    Note

    Seat pillar and sill trim tabs underneath seal

    

94. Move 60 seat to original position

    

95. Move RH front seat to original position

    

96. Move LH front seat to original position

    

97. Raise all four windows
    Note

    Via LH front door switch

    

98. Run ODIN routine PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
99. Unlock the vehicle gateway. See Gateway (Unlock).
100. Run ODIN routine PROC_VCLEFT_X_2R-SEAT-RECLINE-CALIBRATIONvia Service Mode:Low Voltage ➜ Second Row Seats ➜ Calibratevia Toolbox:(link)
101. Run ODIN routine PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
102. Close all four doors
     Note

     If LV is powered up then unlatch rear doors before closing