23/07/2024 17:30:47

Headliner Trim - Cantrail Trim - LH (Remove and Install)

Correction code 1520068031 1520068032 1520068041 1520068042 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-03-05: Updated images and added note that fastener count may vary.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH doors and lower the LH windows.
  2. Remove the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  3. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  4. Remove the LH IP quarter panel. See Dash Panel - Quarter Panel Assembly - LH (Remove and Install).
  5. Remove the LH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  6. Remove the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  7. Open the LH coat hook.
  8. Remove the LH coat hook screw cover.
  9. Remove the LH coat hook screw.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  10. Release the clips (x5) that attach the LH cantrail trim to the vehicle, and then allow the cantrail to hang from the tethers.
    Informational PurposesAn informational icon, calling your attention
    Note
    Amount of fasteners may vary.
  11. Disconnect the headliner harness from the LH rear maplight.
  12. Remove the bolts (x3) that attach the LH cantrail trim to the tethers, and then release the trim from the tethers.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Amount of fasteners may vary.
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket

Install

  1. Position the LH cantrail trim to the tethers, and then install the bolts (x3) that attach the trim to the tethers.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T30 socket
  2. Connect the headliner harness to the LH rear maplight.
  3. Engage the clips (x5) that attach the LH cantrail trim to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace any missing or damaged clips.
  4. Install the LH coat hook screw.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
  5. Install the LH coat hook screw cover.
  6. Close the LH coat hook.
  7. Install the rear header trim. See Headliner Trim - Rear Header Trim (Remove and Install).
  8. Install the LH upper A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Upper Trim - LH (Remove and Install).
  9. Install the LH IP quarter panel. See Dash Panel - Quarter Panel Assembly - LH (Remove and Install).
  10. Install the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  11. Install the front header trim. See Headliner Trim - Front Header Trim (Remove and Install).
  12. Raise the LH windows and close the LH doors.