2026-04-03

Hinge - Upper - Rear Door - LH (Remove and Install)

Correction code 1133071061 1133071062 1133071101 1133071102 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Open the LH rear door and lower the LH rear window.
  3. Apply masking tape to the B-pillar to indicate the hinge position.
  4. Use a floor jack to support the LH rear door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Place a folded microfiber towel between jack pad to protect the door.
    Informational PurposesAn informational icon, calling your attention
    Note
    Raise the jack until it contacts the door.
  5. Remove the nut that attaches the LH upper rear door hinge to the door assembly.
    38 Nm (28.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  6. Remove the nuts (x2) that attach the LH upper rear door hinge to the body, and then remove the hinge from the vehicle.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the hinge as needed to release it from the stud.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently push or pull the door as needed for clearance.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket

Install

  1. Position the LH upper rear door hinge onto the body, and then install the nuts (x2) that attach the hinge to the body.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the hinge to the masking tape to match previously installed position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently push or pull the door as needed for clearance.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13 mm socket
  2. Position the LH upper rear door hinge to the door assembly, and then install the nut.
    38 Nm (28.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the hinge to the masking tape to match previously installed position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently push or pull the door as needed for clearance.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm socket
  3. Remove floor jack supporting LH rear door
  4. Remove the masking tape.
  5. Remove the floor jack from underneath the LH front door.
  6. Verify gap and flush and adjust as necessary.
    Informational PurposesAn informational icon, calling your attention
    Note
    See
  7. Raise the LH rear window and close the LH rear door.
  8. Raise the LH front window and close the LH front door.