23/07/2024 17:32:23

Passenger Compartment Carpet - End Item, Driver Carpet Assembly, Soft Trim (Remove and Install)

Correction code 1530083071 1530083072 FRT 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the LH front seat fully rearward.
  3. Partially the release LH side lower A-pillar primary seal.
  4. Remove the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  5. Remove the LH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  6. Remove the LH front floor mat.
  7. Remove the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  8. Remove the accelerator pedal side trim. See Passenger Compartment Carpet - Pedal - Side Trim (Remove and Install).
  9. Remove the accelerator pedal. See Accelerator Pedal (Remove and Install).
  10. Remove the LH center floor rail. See Passenger Compartment Carpet - Center Floor Rail - LH (Remove and Install).
  11. Remove the fasteners (x3) that attach the LH seat riser crossmember to the risers.
    Informational PurposesAn informational icon, calling your attention
    Note
    Leave the crossmember in position.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
    • 10 mm socket
  12. Remove the driver carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The plastic portions at the rear of the carpet need to clear risers.

Install

  1. Install driver carpet assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The plastic portions at the rear of the carpet need to clear risers.
  2. Maneuver the LH seat riser crossmember into position, and then install the bolt that attaches the crossmember to the outboard riser.
    35 Nm (25.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 13 mm socket
  3. Install the bolts (x2) that attach the crossmember to the inboard riser.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
  4. Unfold the LH front cabin carpet into position.
  5. Install the LH center floor rail. See Passenger Compartment Carpet - Center Floor Rail - LH (Remove and Install).
  6. Install the accelerator pedal. See Accelerator Pedal (Remove and Install).
  7. Install the accelerator pedal side trim. See Passenger Compartment Carpet - Pedal - Side Trim (Remove and Install).
  8. Install the footwell cover. See Dash Support Frame - Footwell Cover (Remove and Install).
  9. Install the LH lower A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Lower Trim - LH (Remove and Install).
  10. Install the LH mid A-pillar trim. See A-B-C Post Interior Trim - A-Pillar Mid Trim - LH (Remove and Install).
  11. Install the LH side lower A-pillar primary seal.
  12. Install the LH front floor mat.
  13. Restore the LH front seat back to its original position.
  14. Raise the LH front window and close the LH front door.