2026-04-10

Trim - Cantrail - Roof Rail - LH (Remove and Replace)

Correction code 1010025062 FRT 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-04-08: Added step to inspect fender mounting hole and perform rework if necessary.
  • 2025-03-26: Added video and updated steps for latest time study.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. Open the LH doors and lower the LH windows.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Install).
  3. Remove the front underhood storage unit. See Frunk Assembly (Remove and Install).
  4. Remove the LH underhood apron. See Underhood Apron - LH (Remove and Install).
  5. Remove and discard the nut that attaches the front of the LH cantrail assembly to the vehicle.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  6. Remove the LH B-pillar applique closeout. See Closeout - Applique - B-Pillar - LH (Remove and Install).
  7. Remove the bolt that attaches the LH B-pillar applique to the B-pillar.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Release the clips that attach the LH B-pillar applique to the vehicle, and then allow the applique to rest against the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently pry outwards from the bottom to release the retaining clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    The applique does not need to be fully removed from the vehicle.
  9. Remove the LH sail baffle applique. See Applique - Sail Baffle - LH (Remove and Install).
  10. Remove the LH C-pillar applique closeout. See Closeout - Applique - C-Pillar - LH (Remove and Install).
  11. Remove the bolt that attaches the LH C-pillar applique to the C-pillar.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  12. Release the clips (x2) that attach the LH C-pillar applique to the C-pillar, and then allow the applique to rest against the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the bottom of the pillar applique away from the C-pillar to release the clips, and then pull the applique downward to release it from the C-pillar.
    Informational PurposesAn informational icon, calling your attention
    Note
    The applique does not need to be fully removed.
  13. Remove the LH header seal. See Seal - Header - LH (Remove and Install).
  14. Release the rearmost clips (x2) that attach the rear section of the LH roof applique to the vehicle.
  15. If present, remove and discard the nut that secures the cantrail stud.
    Informational PurposesAn informational icon, calling your attention
    Note
    Some vehicles may not have this nut installed.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm combination wrench
  16. Remove the screws (x8) that attach the LH cantrail to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  17. With assistance, release the clips that attach the LH cantrail to the vehicle, and then remove the cantrail from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    The number of clips may vary (x7-x11) depending on vehicle build date.

Install

  1. If not present, apply a butyl patch (PN: 1032246-00-B) onto the LH roof rail body at the highlighted locations where holes are present. Refer to images for locations and butyl application alignment.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not apply the patch(es) below the lower edge of the roof rail. Applying a butyl patch below the lower edge of the roof rail will interfere with the primary seal seating. See image for reference.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply a butyl patch to locations 4-6 (in image) only if hole is present.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a roller to wet out the patch after install.
    Informational PurposesAn informational icon, calling your attention
    Note
    Butyl patch and hole location will vary depending on vehicle build date.
    Figure 1. Butyl patch locations
    Figure 2. Rearmost hole
    Figure 3. Rearmost butyl application

    A-pillar section butyl application

    Figure 4. A-pillar section no holes; no butyl patch required
    Figure 5. Do not apply butyl patch below lower edge of the roof rail
  2. Use a taper step gauge to measure the hole in the fender where the front of the cantrail is attached. The mounting hole should be 8mm in diameter and exposed surfaces should have E-coat applied.
    Informational PurposesAn informational icon, calling your attention
    Note
    Apply additional correction codes for fender replacement and/or rework, as necessary.
  3. With assistance, position the LH cantrail onto the vehicle, and then engage the clips (x7) that attach the cantrail to the vehicle.
  4. Install the screws (x8) that attach the LH cantrail to the vehicle.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  5. Install a new nut (2081194-99-A) that secures the cantrail stud, and then tighten the nut until the panel is flush.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Install a new nut even if the vehicle did not previously have a nut installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Twist the rear section of the cantrail outwards to allow access to the stud.
    Informational PurposesAn informational icon, calling your attention
    Note
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm combination wrench
  6. Secure the rearmost clips (x2) that attach the rear section of the LH roof applique to the vehicle.
  7. Install the LH header seal. See Seal - Header - LH (Remove and Install).
  8. Install the LH C-Pillar applique, C-Pillar applique closeout, and sail baffle applique. See Applique - C-Pillar - LH (Remove and Install).
  9. Install the LH B-pillar applique and B-pillar applique closeout. See Applique - B-Pillar - LH (Remove and Install).
  10. Install a new nut (PN: 2081194-99-A) and washer (PN: 1532506-00-A) that attaches the front of the LH cantrail assembly to the fender.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8 mm socket
  11. Install the LH underhood apron. See Underhood Apron - LH (Remove and Install).
  12. Install the frunk assembly and rear underhood apron. See Frunk Assembly (Remove and Install).
  13. Raise the LH windows and close the LH doors.